Search results

  1. Badlilstang

    Gone 10 Years.. About To Buy A New Stang.. Advice Please!

    Well I have been gone for a looong time.. I am very close to buying a new 2014 stang. Although I have always raced 5 speeds I am looking at automatics.. I drive 2 hours every day in traffic! If anyone can give me some advice please do. I have found a GT premium for just under 30k With Leather...
  2. Badlilstang

    4 guage ok for battery relocation?

    I have a 4 guage amplifier kit left over I can use for power wire. Will this be enough? I do have electric fans and 130amp alt upgrade on this car im working on. Thanks for any info. I tend to like the aduio power cable better as it bends easier. EDIT: I am also looking at this to put...
  3. Badlilstang

    A/C hose cover?

    Is there anything aftermarket out there that can replace the foam cover on the large a/c hose that goes back over the intake? We are trying to replace one that is really torn up with something better. I think ive seen large flex loom type covers but have been unable to find them. Thx for any...
  4. Badlilstang

    Whats your 1/4 mile and RWHP #s?

    Curious what your 1/4 mile and RWHP #s are. Also can you specify what tire you were on or even your 60ft would help. Thx!
  5. Badlilstang

    1/4 mile times.

    Buddy of mine at work has a hard time believing that a 315rwhp fox body can run low twelves.. My times in my 92 when it was a 302 with 315rwhp.. 12.32 1/4 @ 7.82 1/8 I went 7.75 in the 1/8th was my best pass before changing the car which would have been a 12.20 run. Car was 3325 with me...
  6. Badlilstang

    Vortech and PCV valve question.

    My buddies car he just purchased has the PCV valve blocked off in the back. It has a air filter style breather cap on the oil fill tube and the hose for the oil fill tube is ran back near the air filter and hooked into the vortech box which just looks like a dust guard to me for the main air...
  7. Badlilstang

    Quarter window trim covers.

    I see them on ebay and they looks fairly nice. Has anyone tried these out on their fox? I read its ABS plastic and you just scuff the originals up and then glue them on. My buddy has one real nice one on the driver side but the passenger side looks pretty bad. If anyone has any pics that...
  8. Badlilstang

    Suspension help please.

    Helped a buddy do some suspension work on his 88 LX.. when we dug into the front end we found original shocks we replaced along with some C-springs, MM Caster Camber plates, and polyurethane spring bushings which seems to have helped the car out a lot. What I did notice is both ball joints had...
  9. Badlilstang

    Rubber piece in center of springs.

    Its been a while since I lowered a mustang and I cant remember if I should keep the rubber piece thats in the center of the spring and re-use it or just trash it?
  10. Badlilstang

    Need your opinion.

    Picked up a supercharged LX for a buddy that is pretty damn clean with new paint but the engine by is a different color... car red.. engine bay maroon. It looks nasty and we are going to gut the engine bay and repaint it... we thought about just doing the engine bay black.. or should we try to...
  11. Badlilstang

    Stang help.. catalogs and blower info.

    I havent owned a stang in over a year but a buddy of mine talked me into helping him find one so we finally did. Its a 306 with a Vortech on it. I know very little about blowers as ive always been a nitrous guy my self. The car runs real strong but I dont think it runs the 10.80s the guy...
  12. Badlilstang

    How to replace an intake.

    I have a 98 GTim doing an intake swap on. I have never touched a 4.6L and I am mostly used to the 5.0L EFI and Carb setups. Is there a guide out there for doing an intake replacement? I already have the new intake and im looking to get to work on it.. Thanks for any help!
  13. Badlilstang

    Car keeps dieing at idle?

    This started a couple years back but would rarely happen.. today it has become really bad and dies all the time. Car will not idle by its self. This is a bone stock 98 mustang.
  14. Badlilstang

    Cant find this....

    Im trying to find the part that blocks off the hole thats left in the firewall when you remove the computer harness.. its the large oval hole on the passanger side of the car. Ive seen plastic block offs that pop into place but I cannot locate one. Anyone know where to get these?
  15. Badlilstang

    Sold my car....

    I hated to get rid of my 95 but its been more of a hassle then anything. Plus the poor gas milage didnt help any. Sold it for 12K to someone I know... gave them my stock wheels along with the new chrome Cobra R wheels I just had put on it and 4 piece clear cobra head lights still in the box...
  16. Badlilstang

    Running hot with a/c on.. need some advice.

    Car normally runs 180-195 with a/c off...it jumps 10-15 degrees higher when I use a/c. It got up to 210 today and started to go over then I turned off the a/c. Anyone else running into this? Is it possible to add another electric fan to help keep it kewl? Its only 85 degrees right now and I...
  17. Badlilstang

    Clutch noise... little help please.

    This is not the normal noise I would associate with a throw out bearing... it only happens during take off and I have not yet been able to duplicate the noise while sitting still disengaging and engaging the clutch. It normally happens when I ride the clutch a bit and sometimes even when im...
  18. Badlilstang

    Need some wheel advice..

    Im going to get some wheels pretty soon and im debating between Chrome Cobra R's and Chrome 2003 Cobra wheels.. (Not the new Rs)... both wheels are 17x9 and both will not be replicas. Just need some opinions on what would look best.. my car is a white 95. Im also curious on wich wheels are...
  19. Badlilstang

    Need pics of Chrome 17x9 bullits on an SN95!

    I live close to wheel replicas and im thinking of getting some chrome 17x9 bullets.. id get the 10.5" for the rear but im not about to pay for the wheels id want to put on it.. if anyone has a pic of 17x9 chrome bullets all around please post it... thanks!
  20. Badlilstang

    Dynoed 331 with new cam...

    The old cam was custom grind from the shop who orginal that did my motor. It was a nitrous grind cam orginally.. .the new cam came from FTI and produced more overal HP and TQ.. not a huge difference at the top but if you look at 3,000 to around 4,500 the FTI cam produced a good amount more low...
Top Bottom
Back
Forums
Menu