Search results

  1. S

    Tachometer only works while cranking

    Since i have relocated all my wiring behind the fenders and dash my factory tachometer will only move (appear to work) while im cranking the starter. After running the tach just reads 0. I have a MSD-6AL also. What did I miss here? Thanks again for all the help here on the Stangnet, Erik
  2. S

    Tachometer only works while during cranking

    Since i relcated all my wiring behind the fenders and behind the dash my factory tachometer only moves (appears to work) while im cranking the engine to start it. Then it just stays at 0. What did I miss here? I have an MSD-6AL also. Thanks again for all the help here on the Stangnet, Erik
  3. S

    What did I break now? Clutch HELP!

    Here is the info: Newer clutch, and aftermarket clutch quad. I was forced to replace my adjustable clutch cable (POS) with a factory unit to get my car home. The non adjustable cable just barely would dissengage the clutch enough to shift into gear. The next day the cable had stretched and it...
  4. S

    Tach not working. Please Help.

    Im just finishing up with a big wire hiding project and my factory tach isnt working properly. I have a MSD 6AL and while the engine cranks the tach appears to work just fine but once started it just reads 0 RPMS. Please help. :flag:
  5. S

    Can I use regular vacuum line for this?

    I just got done hiding all my engine bay wiring. Ive relocated the EGR vacuum solenoid to inside the passenger fender, this is the solenoid with green and red hard plastic vacuum lines to it. I now need to route vacuum to this solenoid and i would like to keep it out of site and probably run it...
  6. S

    Engine bay wiring help needed

    Well ive decided to relocate my engine harness and wiring behind the dash board and i have a few questions. I no longer have cruise control so do i need to keep the connectors pluged into the speed control amplifier? I know that the VSS sends a signal there but if i toss the amplifier will my...
  7. S

    73mm C&L MAF inlet O.D size?

    Ive searched the threads but cant find the outside diameter of a 73mm C&L MAF(Inlet side). Can somone tell me the measurements please. Thanks Erik
  8. S

    Need help finding correct BAP sensor!

    I have a 90gt 5-spd with 351 swap and it needs a BAP sensor, but i cant figure out which one to get. I accidently tossed the original sensor and im having trouble finding the correct replacment. I purchased BAP sensor E8EF 12A644-A1A with wire colors: blk/wht, org/wht, and grn/blk. Problem...
  9. S

    Please help fuel pump not turning on!

    Ive been through many of the no start check list threads already but i just cant pinpoint why my fuel pump wont turn on. Ive already replaced the fuel pump relay and still its not priming. The wiring diagrams for my 90 5.0 show four wires to the fuel pump relay and my car has 4 wires but one...
  10. S

    How low can a Fox go?

    I checked the threads and found nothing, so here goes. I installed the air bag suspension this year and im very happy with the results. When compared to the stock suspension, it rides better then stock even when lowered. Now being able to control my ride height of my car got me thinking. With...
  11. S

    Odd drivetrane vibration! Help!

    ok before i did the following mods everything was fine. I installed rear upper double adjustable control arms, pro 3 industries lower control arms, and new rear spring insulators. My pinion angle is in check. Now when i take right hand turns above 20 mph, even the slightest turning of the...
  12. S

    351W build sheet questions? @@@@@@

    This is my stock stroke 351W engine components, I dont know some of the specs i just have whats written on the build sheet. CS 1020R Melling cam <-- Unknown specs, do you know what brand? Kieth Black 151- .030 pistons <-- are these pistions domed? Raise C/R? Lightning Heads 68cc <-- is...
  13. S

    I cant hook up! Help me out!

    My car has a complete stock suspension, im running 17x9" rims with 255/40/17s. My best E/T was 13.6@105 with 2.25 60' times. I really want to lower my E/T's hopefully into the 12s. I have 275 RWHP and 355 RWTQ. Where can i start to help me hook up better? To run MT E/T drag radials will i have...
  14. S

    Tilt steering column conversion!

    I have a 90GT with air bag and non tilt steering column. I would like to convert to a tilt unit but have no idea what year stang to take one from or if its even possible. Can anyone help with this conversion?
Top Bottom
Back
Forums
Menu