Search results

  1. 3ponyshow

    Been Awhile...

    Last time I was here the New Edge was the rage and we were arguing whether or not 390 was the rear wheel or crank horsepower of an SVT Cobra. Now discussions seem to be mostly about how to keep our aging stuff running. Anyway, glad to see there are some real nice looking SN95's still here. I...
  2. 3ponyshow

    Expired A Pillar Pads

    For 67-68 Mustang. Bought brand new but never installed. Bought by mistake. $50.00
  3. 3ponyshow

    Expired Stock Gears/control Arms

    Stock 3.23 Ring & Pinion Set. Out of my stock '02 with only about 2K miles. $90.00 + Shiiping Stock upper/lower control arms. Only about 8k miles. Offer.
  4. 3ponyshow

    Installing A Power Pipe On A Vortech

    I'm thinking of installing an Anderson power pipe instead of dropping my pulley size smaller. I've heard a few things about the installation that concern me. I've heard it requires a larger hole cut for the pipe to fit through the wheel well, which isn't so bad, but in the directions I read...
  5. 3ponyshow

    Flexplate Question

    I just installed a new flex plate on my 302 and when I put it back together, it seems to have a slight warble to it and is banging on what sounds like the bell housing. This plate matched up perfectly with the old one but is a 50 oz instead of the 28 oz that was originally on it and was the...
  6. 3ponyshow

    Window Alignment

    While re-installing the windows during the rebuild of my '68 Coupe, there's a 1/2" gap at the top of the driver window. The vent window lines up perfectly, as do the doors and I have all new weatherstrip. What am I missing? Is there an adjustment on the regulator I don't see?
  7. 3ponyshow

    Pillar Pads...Yes or No

    I'm not sure which way to go on this. I don't think my '68 Coupe project came with them originally since I don't see any holes and the pillars were painted the same as the interior. So I have 2 options. If I don't put them in, how does the headliner attach at the pillars? The headliner...
  8. 3ponyshow

    Another engine ID.

    I've been doing the research and looked at every thread I can find, but still don't have the info I need. Above the starter on my block is stamped: 26 ETTE From what I've been able to find, that indicates my block is from the 80's and it's a truck engine built by Ford, but still doesn't indicate...
  9. 3ponyshow

    Installing '68 Coupe Windows

    So I installed the new headliner and sent the car to the paint shop. It was my first headliner job and though it wasn't perfect, I was pretty proud of it given my amateur status. Anyway, the paint shop has a glass guy they use and for $100 he installs the glass. I just got the car back and the...
  10. 3ponyshow

    SN95 Ring & Pinion Set, FR EV1 30 Lb Injectors

    I have the original 3.23 gears out of my '02 Mustang. I pulled them with about 2K miles on them, so they're essentially brand new. I also have Ford Racing EV1 30 Lb Injectors in excellent condition. Maybe 6K miles on them. I upgraded to 42's for my new set up. Make me an offer. You...
  11. 3ponyshow

    Trunk lid end cap

    Hi all, I'm putting a 68 coupe back together and am wondering if the the trunk lid end cap has a gasket or seal. I can't find one anywhere, but metal on metal seems unusual to me. Thanks!
  12. 3ponyshow

    Is an 8 rib pulley upgrade really necessary?

    How many of you guys are running 400+ bhp with 6 rib setups? I realize I l live in a high DA area which makes a big difference but... :shrug: I'm already running a 3.125" on my centri (3.33" is what Vortech normally equates to 10 lbs). My tuner says I need to upgrade to an 8 rib setup if I...
  13. 3ponyshow

    New Best Times!

    After my last trip to the track, my car felt like it was hitting the rev limiter and I took it in for a look see. Long story short, my pumps were at 100% duty cycle and endangering the health of my baby. So after what turned out to be a fairly extensive balancing process, I ended up making all...
  14. 3ponyshow

    Another Kenne Bell Boost-a-Pump Install question

    Okay, I've looked all over the place and gotten all the information I've been able to find on this. Unfortunately, alot of it is conflicting. Even on Kenne Bell's own directions! I have a schematic that shows to cut the Brown/Pink wire and then a suppliment page thsat says to cut the Pink/Black...
  15. 3ponyshow

    80mm-90mm MAF upgrade

    I'm upgrading my MAF as well as some other things and have a question I couldn't find the answer for in a search. In '02, the IAT sensor was separate and I have 4 pins in the MAF plug. The IAT sensor is in the inlet pipe of the S/C. Now upgrading to the Lightning MAF, the plug has 6 pins. Do...
  16. 3ponyshow

    Need some recommendations on a fuel pump

    So I'm at the dyno and my A/F is crapping out at about 5800 rpm making it very dangerous to put into boost. My Tuner says the duel Steeda pumps (came with my mongoose setup) aren't getting the job done. He also said I'm pushing my 30 lb injectors and really should upgrade to 42 #'s. My...
  17. 3ponyshow

    What kind of car is this?

    It wasn't a match for the Stang, but it was pretty quick. What is it?
  18. 3ponyshow

    Line Lock vs Trans Brake

    I have a basic understanding of how they both work, but for a 4R70W, which works better for the strip? Which is more cost effective?
  19. 3ponyshow

    Painted Calipers...Cheers & Jeers

    Though I will eventually upgrade the brakes, with only 9000 miles on the car I knew it may be long time before that happens. I've seen this done on other cars but was fairly underwhelmed with the results. Eventually, I just decided to give it a try and thought I'd share the experience in case...
  20. 3ponyshow

    My baby needs a name.

    So I've been thinking a long tiime for an appropriate name for my ride. I want to name her after the goddess she is. Choose from the list of names, their origins and their meaning.
Top Bottom
Back
Forums
Menu