Search results

  1. ozstang65

    DIY Headers

    Hi All, anyone out there tackle the construction of their headers themselves? I was wondering if there's any design literature/tips available. My bucket-of-bits should be arriving before Christmas - should keep me amused for a few days....
  2. ozstang65

    '65 DIY Windscreen Replacement - possible?

    Anyone ever gone the DIY route with front and rear screen replacement? I have the new rubbers and the old screens. (I'd have liked to get a laminated screen but the budget's not quite there at the moment so I'm going with what i've got.) The seal looks like a similar construction to my old...
  3. ozstang65

    '65 Roof Rail seals

    Hi all. The jigsaw puzzle that is my Mustang is finally being pieced back together. I've reassembled the rear 1/4 window assemblies today, which actually went together easier than I remember them coming apart. I have one question regarding the roof rail seals. I have used Sikaflex to seal...
  4. ozstang65

    New aRRSe end....

    They sent me a promo brochure today - check it out. Interesting
  5. ozstang65

    Hydraulic Throw-Out bearing fitment issues...

    I know there's a few of you out there who are running a H.T.O.B. I have a QuarterMaster unit which I will be using, hopefully, in a few weeks time. I went to do a trial fit-up the other day and found that it wouldn't fit over the input shaft housing (Toploader). It's not far off, 30mm I/D and...
  6. ozstang65

    OT: Firefox again

    I recall a discussion a while back about the Firefox Web Browser that was eventually pushed into the talk section. I've posted this here so that the majority of the forum's viewer's can pick up on it straight away. It was only a matter of time really... see...
  7. ozstang65

    Door Reassembly. On-car or off-car??

    Hi Everyone, I'm nearing the point of door reassembly on my '65 coupe and I'm wondering if it's easier to reassemble the glasss/locks before or after I bolt the door to the car.(I personally think it's going to be a nightmare either way!) Hints and tips from anyone who has attempted either...
  8. ozstang65

    Fuel System Design - from the ground up

    Ok, here's the story. My '65 is approaching the final stages of its complete rebuild - among other things it's time for the fuel system. Originality is not even close to being an issue here! Initially I will be running a 4 barrel Autolite but eventually I will be stepping up to EFI so I am...
  9. ozstang65

    Policy Change

    :shrug: ???? Why are we then affronted with hyperlinked pop-up ads in our general topic threads nowdays? Not complaining....just curious......
  10. ozstang65

    HPX Ignition

    Just doing a bit of research the other day and came across this website: http://www.electromotive-inc.com/products/hpx.html I was just wondering if anyone here has used this multi-coil, crank-fired setup and has any comments?
  11. ozstang65

    302 Crank/Waterpump distance

    Anyone happen to know offhand the crank to waterpump centreline distance on a 302?
  12. ozstang65

    Serpentine Belt Pulley Sizes

    Hi all, I've posted this in the classics also as the application is into a '65, but I think the answer might be more easily found in the more modern era.... I'm in the process of setting up the serpentine belt for my 302. Due to the use of non-standard components, I'm fabricating the...
  13. ozstang65

    Oil Pressure Switch Ignition Cutout

    Had a thought the other day to possibly prevent engine damage. The idea was to hook up the ignition through a relay connected to the oil pressure switch. The theory being that if the oil pressure dropped to a critical level then the ignition would cut automatically. This could also be linked to...
  14. ozstang65

    Serpentine Belt Pulley Sizes

    Hi all, I'm in the process of setting up the serpentine belt for my 302. Due to the use of non-standard components, I'm fabricating the entire setup myself. (Also the locations of the components are being located to better suit right hand drive.) My question is, what are the diameters of the...
Top Bottom
Back
Forums
Menu