Search results

  1. 9

    tuner just said 95 mustang is tuneport injection

    My 392 is broke in finally and I need to get it tuned. Called the tuner here and he said that he could check A/F ratio but I'll he could do is the timing and the fuel pressure without an aftermarket ECU like PMS or Tweecer or any of those. Is this true? He can't burn a custom chip for me...
  2. 9

    what size slicks

    I've done a search and a lot of people use 26x10.5x15. Now is this ET streets or true slicks? Reason I"m asking i don't want to buy that size of slicks and have them be to big and not fit. I plan on using weld racing prostars 15 x 8. Tell me what you guys think. update on the 351w... The...
  3. 9

    well my fan just took a *****

    I was just driving around and everything was g2g and then I went to gtech my car... Everything went well except a gteched a 14.9 @ 98 mph (I hate Idaho's elevation) Then driving back to my place I started to smell like something electric was burning so I shut my fan off and made it home and...
  4. 9

    whats everyones daily driver?

    Looking for a daily driver because of these insane gas prices. And just a hunch but I don't think the 392 will get to good of gas mileage. I was thinking of like new nissan ser, wrx, or just find a beater honda civic. thanks guys nathan
  5. 9

    OT: Birthday Present came today

    :banana: :banana: Going to wire it in this wkend and test it out...
  6. 9

    anyone chaned the syncros on a tremec?

    How hard of job is this? I'm going to putting in the 351 next month and I want to change 2nd and 4th gear syncros... any help would be great. thanks nathan
  7. 9

    where does the IAT sensor go/ 93 down tb

    where does this sensor go when you swap to this setup? My 93 down powerpipe does not have a fitting for this? thanks nathan
  8. 9

    need 2 reccomendations

    I'm almost finished with buying stuff for my swap. 1. Oil Pump 2. Head Gaskets Also have question about a FTI cam, will Ed sell me the rockers, pushrods, timing chain? Thanks nathan
  9. 9

    It has arrived!!!!

    392 fordracing shortblock,Well finally get to do some actual hp upgrades, I hope to have it running in june, i have afr 185 non emmission legal 61cc heads coming with upgraded springs and i already have a trickflow r intake to strap on the top of it. :nice: nathan
  10. 9

    need a little help on my new TB

    I just received my new accufab 75MM tb for 87-93 mustang and I need to know what sensor goes where especially the one on the bottom of the TB which you'll see in the pics. And can i re-use any from my 95 TB thanks nathan which one on this side? and this is the bottom which sensor goes...
  11. 9

    garage floor epoxy *pics*

    Well I noticed a thread about a wk ago about the Epoxyshield Rust-oleam (sp) garage floor coating. Well I have some before and after pics of my garage that I just finished tonight. Hope this helps you guys. nathan
  12. 9

    engine struggling from 80 to 100

    just put my 3.73's in and and i downshifted into 4th and ran it up to about 105 and it felt like it would not miss but skip a beat like the ac compressor kicked but i know that didn't happen. i'm going to do a compression check in my motor and pull a spark plug to check that because i also...
  13. 9

    ECTED gets installed tomorrow !!!

    ECTED gets installed tomorrow !!! Installed *pic* Well tomorrow is the big day finally get my 3.73's in and my ECTED locker. I ran the wiring for the switch tonight so it should be just like a locker install for the shop. Also putting in 31 spline superior axles. Hope nothing drastic...
  14. 9

    The UPS man was busy today

    Ordered the new Auburn ECTED (electronic locker), and 31 spline superior axles. Finally get to put my 3:73's in. ECTED Axles Getting it all installed on the 19th. I can't wait.. get rid of this highway gear. nathan :D
  15. 9

    would i overheat with a aluminum 351 block?

    I'm trying to build up a 351 motor and having problems finding a block. I've looked for more than 6 months to find just a plain roller motor out of a f-250, bronco, van. I don't want to do the retro lifter thing, and I was going to do a sportsman but those things are high 11 to mid 1200 dollar...
  16. 9

    cons of retro fit lifters and non-roller block

    I'm trying to build a 393 for my 95 GT and I'm having a hard time finding a roller block for a foundation and I don't want to spend 1200 dollars for a sportsman. I want to run hydraulic cam so what are the disadvantages of going the non-roller block and use retro lifters. thanks guys, nathan
  17. 9

    carfax report

    5TEWN72N22Z114601 thanks guys
  18. 9

    Fox TB setup...good info inide

    Fox TB setup...good info inside I don't know if it has been posted over here or not I found it on the corral. This topic has been pretty steady on the forums lately here's just another little piece to help us out. " part for sn95 to fox body t.b part number for tps ext harness is...
  19. 9

    new webpage

    hey guys this is non-tech but thought you guys might want to check it out http://www.95mustanggt.com by the way still a lot of work to do.. thanks nathan
  20. 9

    global west subframe connectors which ones

    I'm looking at global west subframe connectors and I'm wondering whats the difference between the round tube regular $145 subframes and the four tube rocker support subframe connectors..$150 ones. Are the four tube connectors and add on? I'm really uneducated about these things. Would I be...
Top Bottom
Back
Forums
Menu