Search results

  1. J

    Expired Hot Side Turbo Kit

    Up for sale is a stainless steel turbo hot side for 302. Included are the two headers, crossover pipe, and 3inch down pipe. The pass side header has been modified the T4 flange has been turned to make the turbo sit sideways and below the flange is the waste gate flange has been welded. There are...
  2. J

    Expired Edelbrock Performer Heads

    I have a set of edelbrock performer heads for 302/351. They have been ported very nicely. Two of the pushrods ports have sleeves installed because of the porting. They are pedestal mount rockers which are included crane cobra 1.7 ratio. The heads have been gone through a few years back which...
  3. J

    Expired Turbo Hot And Cold Side Top End Engine 8.2

    Changing combinations I am selling single turbo hot and cold side (no turbo or waste gate ) and top end components with E85 tune for SBF 8.2 deck includes Hot side side turbo mounts side ways on pass side ( no turbo or waster gate) Cold side 3 inch dia starts on pass side enters engine on...
  4. J

    Expired Mega Bite Lower Steed Uppers

    Mega bite jr lowers and boxed steed uppers good condition 125.00 Thanks for looking
  5. J

    k member help!!!!!!!

    I purchased a k member form a private seller I beleive it to be a griggs racing k member. Is there any way of telling if it is for a fox body with 302 and not for a 94-95 or a 96 on 4.6? I'm pretty sure the frames are all the same from 79 to 04 so i think it will bolt to the frame holes but the...
  6. J

    THE BEST WAY TO INSTALL LONGTUBES ON A 4.6

    What is the best way to install longtube headers in a 97 GT 4.6? Any help would be appreciated!!!!!!!!!!!:shrug:
  7. J

    TO DO OR NOT TO DO ELECTRIC WATER PUMP

    You guys who run electric water pumps do you still use a thermostat or just a water restrictor? I have an electric water pump with a restrictor my car wants to overheat I believe the hole in the restrictor is too large allowing the water to move through the radiator too fast. So do I go with a...
  8. J

    97 GT AUTO TO MANUAL CONVERSION

    Does anyone know what I would need to convert a 97 Gt 4.6 auto to a stick shift? I've got the trans, flywheel, fork, throwout bearing, pilot bearing, clutch, cable, pedal assm, and shifter. Do I need to change the computer and what about the wiring? Would the wiring just be unhooked ? If I...
  9. J

    c4 trans install question

    Just installed c4 trans in the 89 musatng trans is bolted up and torque converter is bolted up. The question or problem I have is the engine is very hard to turn with a breaker bar on the crank. Has anyone every ran into this before? As far as i know the converter is seated properly in the...
  10. J

    87-93 aod shifter handle removal

    Does anyone konw how to remove the shifter handle on a aod 87-93 ? Also i need to adjust the selector line to match up with the letters for each gear. If anyone knows how to do both i would really appreciate it . Thanks jason
  11. J

    HELP!!! WIRING ALTERNATOR MASTER DISCONNECT SWITCH

    HELLO I'VE GOT THE BATTERY RELOCATED TO THE BACK AND THE MASTER DISCONNECT SWITCH MOUNTED AND WIRED. I NEED TO RUN THE WIRE TO THE ALTERNATOR AND I CAN'T GET THE RIGHT INFO FOR THIS. FIRST WHAT SIZE WIRE? SECOND DO I CUT THE ORANGE AND BLACK ALTERNATOR WIRE AND RUN THE WIRE THAT GOES TO THE ALT...
  12. J

    fox brakes suck

    just did brakes on the 89 gt last july new pads, calipers, rotors, hoses, and flushed the whole system and thebrkes still suck. i know the fox brakes are not the greatest, but the car had to of had better brakes when it was new coming off the production line! the pedal is firm no air in the...
  13. J

    93 cobra tail lights

    can anybody tell me the size of the stripes that are used on the 1993 cobra tail lights? i bought a pair of 86 gt lights and i want to stripe them. thanks jason 89 gt
Top Bottom
Back
Forums
Menu