Search results

  1. Cammed90Notch

    The best supercharger. . . . . .is a turbocharger.

    Just face it and stop "whining" :p I dunno, it seems as if SCers still rule the Mustang scene, but that seems to be fading, and fast at that. SCers have their place, they can make great power, they have a nice whine at idle, but the power curve and RPM at which full boost is what holds it...
  2. Cammed90Notch

    What all is involved in removing the brake booster (working on engine bay)?

    Well, Simpy put, I recently painted my engine bay after sanding it down, but I didn't remove the brake booster. That along w/ a few other things, I'm basically not happy w/ what I did, so I'm going to go back and redo the engine bay. So I was wondering, what all is involved in removing...
  3. Cammed90Notch

    Need to upgrade to 33 spline axles, what all has to be replaced?

    Couldn't I just keep my differential and get new carriers for it? What all needs to be replaced, I suppose I'm going to need to get C-clip elims as well :nice:
  4. Cammed90Notch

    I just got my fuel cell in, I have a weird or dumb question, I guess

    So, I have a new RCI 16 gallon fuel cell (sumped/drag cell) and I also opted to pay the extra $20 for the safety foam. Well, I was expecting the foam to be external type foam, but it's black foam on the inside of the fuel cell. Is this how it's supposed to be? I guess this helps it from...
  5. Cammed90Notch

    Found a good way to clean carbon off pistons/what tools do I need to port?

    Howdy, I've been piddling in the shop downstairs working on the stock E7TE heads and I've been cleaning off carbon off of my old pistons (though I won't be using them, just wondering how to get it off best). Well, first off, how to get the carbon off easily :flag: In my Dremel tool kit...
  6. Cammed90Notch

    Help me I'm desparate! I need to get rid of this rust

    Hello, I need to get rid of this rust. In the pic, you'll see that the panel seems to be attached to the lower door opening as wel. What's the best way to replace this? I want this rust gone, and I don't mind doing a little work, as I've been working quite hard on the car for the past few...
  7. Cammed90Notch

    so what are the cheapest aluminum heads for a 5.0?

    so does GT40 (Ford) make some good priced aluminum heads? http://www.streetfly.com/S_cylinder%20heads.asp Is this site right, $400 for new GT40 aluminum heads? :flag:
  8. Cammed90Notch

    FINALLY got my engine+transmission pulled!

    After breaking several tools, welding them back together, distorting myself in all kinds of unhealthy positions under the car, cutting a big chunk out of my right index finger, I got the drivetrain pulled :nice: :flag:
  9. Cammed90Notch

    Pulling engine and transmission w/ car flat on ground, do I need to remove starter, &

    Hey, I'm pulling the engine and transmission for the first time w/ an engine hoist w/ the car flat on the ground. I was wondering, do I need to remove the starter? I know I have to unhook any wires from it, but do I need to remove it since the transmission is coming out too? The "engine" is...
  10. Cammed90Notch

    Suggestions on welding holes in the engine bay?

    Hey, I'm about to remove my engine and tranmission for the first time :flag: Well anway, I was wondering what your suggestions were for welding the little holes in the engine bay shut (the ones I don't need, which are many. I have a Hobart 135 MIG welder w/ flux core wire (I am planning on...
  11. Cammed90Notch

    Who sales the best-buy forged pistons for a 306!

    Howdy, I'm rebuilding my engine and was wondering who has the best pistons for a 0.30 over pistons for my car. I'm looking for some good forged pistons that will be able to sustain a 150-200 shot of nitrous w/ about 10:1 compression or so. So who sales the best/most economical pistons like...
  12. Cammed90Notch

    How do you build a relatively cheap 331?

    Could a use maybe a steel Scat crank (around $300 I guess) hyperpistons or forged and some rods (I beam) and hopefully machine work won't be too much
  13. Cammed90Notch

    PICnsd:What's the best way to remove a strut tower brace? (I know, stupid quiestion)

    Hey, When I bought my car it had a chrome strut tower brace. I was wondering what the easiest way to remove the strut tower brace is? Do I have to remove the fenders? :shrug: This is what it looks like (pics is from a few months ago when I was deleting the AC)
  14. Cammed90Notch

    I have a AOD w/ shiftkig and 3.73 gears, is it worth getting 4.10s?

    Hey, I was wondering. I have 3.73 gears and I have an AOD. I was wondering if it would be a good investment to put in 4.10s? I would like the kind of low end torque a 5speed has, so would this help? :) The previous owner put in the 3.73 gears, so that's why I have them. I also am...
Top Bottom
Back
Forums
Menu