Search results

  1. 88stangmangt

    For Sale Borg Warner & precision turbo plus other parts

    All parts are new in box from a turbo project that never happened. All parts Have never been installed or ran. Prices are marked as OBO. Local pickup in the Richmond, VA area is preferable but shipping is an option too. 1. New. Borg Warner S480 Billet 80 Comp 96 Turbine T6 1.32 A/R housing...
  2. 88stangmangt

    Help me pick my H/C/I Combo.

    Long story short i have a nice T-top 88 GT with a Worn out 200k mile 302. Also i have another 86 notch with a fresher 302 im wanting the short block out of that car. So while i have the motor out i figured a set of AFR 165'S,B303 cam(not looking to dump big $$ on a custom cam) and a set of some...
  3. 88stangmangt

    Elec problems...experts help needed

    ok here is the problem im hopeing some one will help that messes with them more than me...my headlights dont work...only do they come on when i turn the key all the way over to engage the starter...cant figure that one out my runners stay on all the time in the rear...i have already completly...
  4. 88stangmangt

    which temp sender??

    which one of the 3 senders in the lower intake and one in the block run the stock temp guage???
  5. 88stangmangt

    did i get the wrong TB

    its off a 96 mercury montianer 65mm TB i just drilled it out to fit on my ported upper and having it on there i have to push the lever with the ball on it forward to open the butterfly....my mustang is not clost by so i cant look how it is did i get the wrong tb to use??it was free so im not out...
  6. 88stangmangt

    Waste Gate hook up

    Going over everything before i take it back to the dyno the end of next month for the final tune....Last time i had the WG hooked up wrong i believe....since it has two ports on it side and top which one is the boost referance sent to?? top? and the other remains non hooked up? i dont want to...
  7. 88stangmangt

    snow kit....any luck??

    bout the MAF kit from a buddy used a couple time he wasnt happy with it...looks like he didnt even have it hooked up right. he sold it for 200 anyone had any luck it???
  8. 88stangmangt

    Need quick bell housing help!!

    have the chance to buy a 70's C3 Pinto bell would this bolt up to a C4?? If not then ill keep searching for the impossible to find housing.
  9. 88stangmangt

    5-lug swap rear axle question(searched)

    Today while i was at the JY i got a set or ranger axles both from a 97 ranger DS both the same length. But once i got them home i put them next to my mustang 4-lug axles and they are atleast 1/2" longer...can i not use 97 axles?? will the passanger side be 29-5/32 like i need??? I hope im not...
  10. 88stangmangt

    New motor back,first dyno run.

    Ok so as we stand now im maxing out the VAM at 3krpms...causing it to run lean....we were attempting to program a SCT chip. I didnt get any honest runs in becuase we had to keep shuting it down at 3k...but at that time(3k) it was seeing 14psi with a massive torque jump. so im in the process of...
  11. 88stangmangt

    coolant sensor/electrical help

    which sensor belongs to the temp gauge and what color wire goes to it?(is the sensor on the side of the block under the oil pressure sending unit?) also does anyone have a diagram for the fuse panel to tell which fuses do what - cause mine is missing - my haynes manual doesnt tell?
  12. 88stangmangt

    Took some Temps of the new motor....

    After a mile or two easy put put run i took the following temp reading to see where i stand. #4)169 #3)240 #2)130 #1)100 Dp)360 turbo exhaust side)350-400 These readings are off the primary's off my Stinger Centermount header at the base of the header All reading in Ferenheight. They do...
  13. 88stangmangt

    Injector buzz!!!

    so im geting a Humm from my injectors/rail....which is what i believe to be the reason my car isnt starting now....i first thought my cylinder was loading up with fuel.I have to take the hybrid off to get to the plugs. but with the injectors and rail out of the intake the buzz is still present...
  14. 88stangmangt

    Fuel pump problem...

    ok well....i got my 255LPH pump and new sender in....car cranks....no hot to the F/P. I have a constant hot to the relay under the seat....and if you branch it from the green wire to the pink the F/P will kick on no problem...but im just not geting a exciter wire coming in to kick the relay...
  15. 88stangmangt

    Hunting down my winter project...

    well with my 2.3T almost done and out of the way (last winters project) im looking for my next...i found a 460BB i believe out of a 70's 250..all ready has a weiland intake on it...300$ with c-6 which i cant use because it has a transfer case on it...but i have plans for a eagle 514 kit and a...
  16. 88stangmangt

    Couple beers and a few dollars later. *pics*

    looks awesome turbo looks tiny now that the brackets are on... I used the ranger ALT bracket so i could later have my intake flipped without problems...this is how much clearance i have between the WG and back of the ALT but it fits... This is why the motor hasnt went in yet im...
  17. 88stangmangt

    Svt Contour Seats?

    well long story short walking around my pick and pull JY i happen to spot a Black SVT Contour in the new arival section. Well got to looking and behold a perfect set of leather seats Almost black were in it. 98 Contour seats NO cracks,rips,stains noting(DS power everything) i couldnt pass them...
  18. 88stangmangt

    SVT Contour Seats?

    well long story short walking around my pick and pull JY i happen to spot a Black SVT Contour in the new arival section. Well got to looking and behold a perfect set of leather seats Almost black were in it. 98 Contour seats NO cracks,rips,stains noting(DS power everything) i couldnt pass them...
  19. 88stangmangt

    motor pics...almost done..

    :notnice: didnt have fun with the gapless rings but all in all the worst is over now.:nice: That Hybrid is a tight fit i did have to turn the compressor housing...but it will have to come off to do plugs and 90* spark plug boots will be needed. now i need a DP/WG and...
  20. 88stangmangt

    For those on the fence about Bo Port. (come on in)

    Everything came well packaged no shipping damage...I was very impressed with how clean and smooth the ports were. I had a stage 3 port job done with big valves installed. I also had a esslinger 2277 cam kit installed. all in all i am VERY please with the workmanship i Know this head will help me...
Top Bottom
Back
Forums
Menu