Search results

  1. bln92cpe

    a Leak in my new Tremec TKO500

    Hello, I had my mechanic install a new aluminum driveshaft and Tremec TKO500 and the thing has a leak right where the driveshaft goes into the Tremec..It is dripping down on my cats causing a lot of smoke when I drive. My car has a new motor, clutch and tranny..Will the leak go away during the...
  2. bln92cpe

    31 Spline 5 lug Axels/ Eaton Posi

    Hey guys, I just bought 31 Spline 5 lug rear axels and an Eaton Posi..My mechanic said I would break my rear axels if I didn't upgrade them due to the amount of power I am pushing..Anyone use this set up or have experience with this..Will it affect drivability on the street. I got both for...
  3. bln92cpe

    NEW SHOP OPENING

    Hey people, listen up..My friend is opening a sick shop for mustangs in Torrance,ca next door to Swansons performance/dyno..Its called ABZ racing, hes cheap and has been doing mustangs since the early 80's..He has done everything on my car and can do anything on any mustang for cheap... my...
  4. bln92cpe

    WANTED:Diagram of Vacuum lines-92LX

    Hello I failed smog because my vacuum lines were not hooked up correctly and some stuff was capped off and not connected..Can you please show me a diagram or pictures of 1992 Emissions/Vacuum lines so I can get my ride registered and driveable..Thank you so much.
  5. bln92cpe

    Saleen Show tomorrow

    Anyone going to the 8th annual Saleen show at their headquarters Sat. Sept.18th...Should be awesome.
  6. bln92cpe

    How far can you push a stock T5 Tranny

    I am about to drop 5 grand on my car and was wondering if my stock tranny would last awhile. The tranny has 135,000 miles on it and i would rather buy other stuff first than buying a Tremec TKO. Are you running a stock tranny or an afterarket and what would you suggest. thanks
  7. bln92cpe

    anyone want to start a saturday cruise in LA

    My car is at my mechanics garage and i get it back next week. If anyone wants to start up a little sat or sunday cruise this summer that would be nice. We could meet at a restaraunt eat and go on a mellow cruise near the beach. I am up for it. We could show off our stangs and make some new...
  8. bln92cpe

    Did Chicane in Torrance go out of business?

    Hello, I drove by Chicane and their Chicane store front sign was taken down and the place was closed and looked empty. Does anyone know if their gone and if so where can I have a 306 installed. Thanks
  9. bln92cpe

    Any stangers in the South Bay

    Anyone have a stang in the South Bay ( Manhattan, Hermosa, Torrance, Redondo, LAX area,LB,) That would like to start up a cruise day on a weekend. I am in Lawndale, ca
  10. bln92cpe

    Purchased CHP 306 Street fighter, a little confused..

    Ok I am having a CHP 306 Street Fighter built for me and in order to fully balance it, the guy at CHP told me he needs the Romac Damper which I have and the clutch and flywheel. That means I have to have the clutch and flywheel yanked out of the LX which I didnt plan on because it will sit in...
  11. bln92cpe

    306 Street Fighter

    Does anyone have experience with Coast High Performance and their 306 Street Fighter. They are in my hometown and I am going there today to buy the short block for $1699 with my tax returns. Is this worth the money for a 140,000mile 1992 Notch. 306 Street Fighter Cast steel crankshaft CHP...
  12. bln92cpe

    tired 302/ 306 rebuild suggestions please.

    My 92 Notch has 140,000 miles on it. I have all the parts for my top end and I was thinking about a new CHP short block for $1699 or should I just bore my origional block .30 over and just replace the internals? Has anyone done this and what internals should I replace. I heard a stock block...
  13. bln92cpe

    New Battery, Car barely starts

    Does anyone know how to put a new starter in a mustang, I think this can solve my problem.
  14. bln92cpe

    Strong Top End/Weak bottom end??

    I have a 92 LX Coupe with 135,000 miles and a Vortech S Trim (8 lbs ) Currently it has a blown Head Gasket and I have these parts to install: TFS Twisted Wedge Heads, 1.72 RR, Hardened Pushrods, Romac Damper,Double roller timing chain, 42LB injectors, ECAM, Saleen upper /lower intake from...
Top Bottom
Back
Forums
Menu