Search results

  1. I

    New Build Starts And Dies

    I just got everything put back together last night on my new engine and went to start it and it starts and runs for a few seconds and dies almost like ignition was switched off. I did not change anything from the last time it was run but that was 2 years ago! Info on what Ive checked: moving...
  2. I

    Progress Thread Ike34's Build Thread

    My stangs in pieces so I figured I would start a build thread (Lots of Pics) The main reason it was completely apart, is that is was going to get painted but that has now been put on the backburner since it needs a new motor. All wiring is getting tucked in the engine bay along with some...
  3. I

    Need Help, Swapping 89 to 90-93 Dash

    Im thinking about putting a newer dash into my 89, Ive been doing some looking to figure out what swaps and what has to be changed. Here is what Ive come up with so far. HVAC Controls have to be swapped or the dash modified Fuse box has to be moved or the dash modified Lower dash panel on...
  4. I

    Anybody Run a 305/45/18 or 295/45/18 on a Fox??

    Im going to be converting my car to 5 lug soon, and I want to run a 28" tire on the rear and was wondering if anybody has run either of those sizes? There going to be going on 18x10 Saleen wheels with fox length axles. The 305/45/18 are Nitto NT05R or NT555R and the 295/45/18 are Nitto NT555 or...
  5. I

    Going 5 Lug, Wheel Opinions?

    Im going to be converting to 5 lug soon, and Im trying to decide on wheels. I think I want to go with 18x9 and 18x10 Saleens. Im thinking of either going with hyperblack or just black. I made some quick photoshops, nothing special just to get the idea. Whats your opinion? Hyperblack
  6. I

    Anybody Make Their Own Discharge Pipe?

    I have an A-Trim with a plastic discharge and a bypass valve fitting screwed in and it blew out of the plastic last night because the nipple on my bypass cracked so my bypass valve wasnt functioning. Im thinking about making my own instead of paying over $100 for a aluminum vortech one...
  7. I

    New Control Arms and a New Stance

    I installed a set of Maximum Motorsports Control Arms with Ajustable Spring Perches. I also installed a 98 Cobra rear sway bar. Im going to raise the rear some, its settled from me driving it, and now its lower than the front Before
  8. I

    Rear Sway Bar Question?

    When I bought my car it came with no rear sway bar and I want to put one back on, I found a 03 mach 1 and a 98 cobra one. Which one would be better? Ive read that the 03 mach 1 is 23mm and it is solid, and also found that the 98 cobra is 25mm but I dont know if it is solid, does anybody know...
  9. I

    Mach 1 Chin Spoiler on a Fox. Pics?

    I was wondering if anybody had some pics of a mach 1 chin spoiler on a fox? Im thinking about doing it on my 89 LX, Ive seen the Latemodel Restorations GT350 but thats the only one Ive seen, has anybody else done it? Post your pics if you got some.
  10. I

    Hatch Area Ideas?

    Im trying to gather up ideas for placing my methanol pump/resevoir, Nitrous Bottle and maybe my battery in my hatch. I want something clean looking, not just stuck in there. Post up your ideas or pics if you hatches with ideas for me. Thanks Todd
  11. I

    Powder Coated My Tubular GT40 Intake

    I powder coated my tubular gt40 intake to match my boss 302 valve covers, thought I would share what do you think?
  12. I

    2 1/16 Single Gauge Pillar Pod

    2 1/16 Single Gauge Pillar Pod Asking $12
  13. I

    BBK Clutch Quadrant

    BBK Clutch Quadrant Asking $20
  14. I

    For Sale: B&M Shifter For T-5

    B&M Shifter for T-5 trans, comes with boot and hardware Asking $75
  15. I

    F/S: GT40 Upper to Lower Studs

    I have 6 studs, 2 long and 4 short, I used them on a Tubular GT40 intake with a 1/2 inch spacer, I believe they will work with a 3/8 spacer to. Long Studs: 7 inches long 5/8 thread on one end, 1 1/8 thread on the other end Short Studs: 2 1/2 inches long 1/2 thead on one end, 1...
  16. I

    New Valve Covers

    Got new valve covers today, I know I dont have a Boss 302 but I think they are going to look good when I get my Tubular GT-40 intake powdercoated to match. Anybody know of any good powdercoaters in or around Iowa?
  17. I

    Spring Idea? Opinions/Advise

    Right now my car is in storage, so Im thinking up ideas for spring when it comes back out. I have been collecting parts but I dont know if or when I should install them. Here is my current setup: Rebuilt 302 unknown amount of miles Vortech A-trim 5-6psi Stock heads maybe ported unknown...
  18. I

    Next Springs Plans/Ideas For My Stang

    Started collecting parts and ideas for my stang for next spring. What do you think? ASP 7 inch Crank Pulley 3.12 Supercharger Pulley Cobra Water Pump Pulley (Have) Tubular GT-40 Intake with ported lower (Have) Heads (unknown which yet) 42lb injectors Vortech T-REx Pump (Have)...
  19. I

    Nice Day + Clean Car = Pictures

    Interior Pics, Repainted everything but the doors, doors and seats are next New Rear Disc Brakes
  20. I

    JBA Longtube Headers

    Has anybody run them? I searched and couldnt find much. JBA makes Ford Racing shorties and Ive seen them and they are real good quality, so their longtubes I would think would be the same. How did you like them? Whats the quality like? How low do they hang? Ive also been looking at other...
Top Bottom
Back
Forums
Menu