Search results

  1. C

    GT40P Headers

    These are not Ford Racing headers. I have a set of shorties that were on my car for 2 years. They were purchased new from Summit when my nephew did the H/C/I work for me. They worked fine and fit with no issues at all. The only reason I took them off was I found a set of used Ceramic FR headers...
  2. C

    Happy with the upgrades!

    I made a trade with my nephew who grew up cutting his teeth on Foxes. He agreed to install some of the parts I've had under the bench waiting ('cause I'm a lazy $hit...), GT40P heads and an Exploder intake with a 75mm TB. He ended up adding a B cam, and headers (I thought my BBK's would fit...)...
  3. C

    Thanks Guys!!

    Just thought I'd drop a line and let you guys know the help you've been. I had a hot start problem with my 91 5.0 Coupe.... doing a search led me to all the info I needed to solve the problem:D It was an ECT sensor. Simple/obvious fix for some of you I know, but not for everyone. Again...
  4. C

    Bent axle...

    I had a driveline vibration and was looking at different things. I put an indicator on my axle flange and found it ran out quite a bit :shock: I have a spare 8.8 rear, are both axles the same length or do I need to use the same side.
  5. C

    Are these '95 spindles?

    I picked these up at a swap to go 5 lug on my Fox. I'm guessing some kind of sensor goes in the hole and reads the little slots? :shrug: Where would the P/N be? I have a pic of the cast #
  6. C

    C+L 73mm MAF Q

    I picked up one of these off ebay and it was supposed to come with 19, 30, and 36 sample tubes. The 2 that were loose were scribed 30 (.510 dia) and 36+38 (.547 dia.). I took the third out because the MAF was filthy and it's not marked but measures .564 dia. with no other markings. I'm guessing...
  7. C

    Why would anybony drill and tap a hole

    on the intake side of a throttle body? I got one off of fleabay and there's a hole about 5/16 thread through the body near the end where the boot would go. It has obviously been added later. Any clues?
  8. C

    Cut a swirl in the EGR?

    Think it would make a difference? I have a 65mm TB, and a 67mm EGR to put on my stock intake. I noticed the opening on the intake is only 63.5mm, might just open that up too. We used to do stuff like that to our bikes when I was racing them thinking that the additional air motion would help...
  9. C

    Swapped my pedals yesterday

    Did some searches, armed with info I was expecting a colossal struggle so I planned to tackle this part of a T5/AOD swap just to get it over with.:( I had the old hanger out and the new one wiggled in, in less than 1/2 an hour...(once I got it loose) It would have been MUCH easier if I had...
  10. C

    I guess I'm not the only one who's had fuel gage prob's

    I did a search and it looks like a pretty common problem with these cars, however it IS irritating :nonono: I have a '91 LX 5.0 Coupe. I love the car but the fuel gage only worked for maybe 6 months after I got the car (3 yrs). I always used the trip meter, but could hear something...
  11. C

    Is this T5 worth the effort?

    I've been looking for a close ratio T5, I know for $1200 or so I could have a new one, but it's just not in the cards right now.:( Anyway I found a T5 at a swap with a 2.95 1st gear. The only problem is it's an '84 (1352-065) That's non-WC, right? I suppose it can't be much weaker than a 4cyl...
  12. C

    what year F150 rear disc?

    I've seen where F150 rear disc will bolt to big bearing 9" axles. I was wondering if anyone knows what years to look for in junkyards?
  13. C

    Header leak

    I have a set of BBK equal length shorties on a 5.0 LX Coupe. I installed them with copper gaskets, but I still think they leak. It wasn't so bad with the off road H pipe as it drown it out. Now that I need a sticker I need to put the cats back in, it's so quiet now you can hear the leak:( After...
  14. C

    Stock 5.0 H pipe measurement please

    If you've got your catted pipe out and handy, can someone measure the diameter of the O.D. of the pipe where the flange bolts to the header just before the flare? Preferably with calipers. I'm trying to put mine back in for smog test and the PS side flange rusted away. I don't want to buy a...
  15. C

    Is it really THAT easy?

    I did a search on this and found some good info. I think I need a new clutch pack in the rear of my `91 5.0 Coupe. The axles have about 1/8" play in and out, although I would have SWORN it was 1/2" or better :( I measured it to be sure and then called a local guy who wants $250.00 + Is...
  16. C

    Help a 5.0 noob

    I have a `91 5.0 LX Coupe. I know thjis is going to sound stupid but I was wondering what the computer looks like and where it`s located. :confused:
  17. C

    `76 Mustang rear

    I picked one up at a swap meet. I thought it had the same bolt pattern as an early 4 lug wheel (`66) but was told by someone that this is incorrect. Were they right? If so does anybody need an 8" rear 3.00:1 open in northeast? :bang:
  18. C

    what size speakers for Fox doors

    I would like to put some speakers in my doors but don`t know what size will fit thanks Jack
Top Bottom
Back
Forums
Menu