Search results

  1. JC6715

    81-95 157t 50oz Ford Racing Cast Iron Flywheel

    Brand new, never even mocked up Ford Racing flywheel $100 or so from major suppliers, I want $75 + shipping for it. 157 tooth, 50oz, 13.25 diameter P/N: M-6375-B302 Casting numbers: rf-eizr6380-a2a & e6zr-aa Check for compatibility with your setup before purchase More...
  2. JC6715

    Steeda Tri-Ax Shifter Handle

    New only mounted for mock up Steeda Forged Tri-Ax shifter handle. Perfect condition. $25 plus shipping
  3. JC6715

    Pulsation / Vibration only when turning right

    My 67 Coupe is driving again. All steering components are brand new and everything is tightened to spec. I've done the granada swap and converted my PS to MS with one of the control valve delete adapters and I have the good "roller" (gusher bearing) idler arm. I am getting a pulsation when...
  4. JC6715

    Rebuilt control valve, too much play in ball stud?

    Just returned from the alignment shop where I was told there was too much play in the ball stud where the pitman arm connects to align the car ('67 Coupe, power steering) properly. They pulled me into the bay and while one turned on the wheel the other showed be how much wiggle there was in the...
  5. JC6715

    Light at the End of the Tunnel

    After two LONG years of the '67 not moving. She is once again moving under her own will! I'm obviously far from done, but had to get a drive in to keep my motivation high.
  6. JC6715

    Quick late model PMGR starter wiring question

    I'm assuming (since there were no instructions included with the starter) that the attached lead on the left is the ignition switched power in, the top big lug is the battery cable in, and the bottom big lug is the ground? Is that correct? It is a mini starter for 93 Ford 5.0 with 157 tooth...
  7. JC6715

    Rubber perch pads?

    Anyone know where to find these? Just roller-ized my perches and don't want to put the nasty cracked ones back on... Checked all the usual suspects websites, but can't seem to find them... Looking for the pads like on these perches Thanks guys
  8. JC6715

    Pinion Yoke Swap Question

    It's time to buy a drive shaft and I want to upgrade my 9 inch's pinion yoke to 1350 u-joints. I not too long ago had the gears set up with a solid spacer instead of a crush sleeve. Quesiton is: Can I just remove the old pinion yoke, install the new one, torque to spec and call it good...
  9. JC6715

    T56 into a 67 Coupe: Surgery required

    Hey everyone, just wanted to post some pics up of the install of a T56 into my '67 Coupe. I am using Lakewood's Muscle mounts on stock frame mounts, and a 302 block. I am getting close to the proper angle, but need a little more clearancing... <center> <img...
  10. JC6715

    315 Tires - Minimum clearance to lower control arm

    Hey guys, just got most of my TCP G-Bar installed. I'm sizing up the largest rubber I can fit and was curious: What is the minimum clearance you want between a stationary part (lower control arm, spring) and the tire? There shouldn't be much run out as I want to run the BFG T/A Drag Radials in a...
  11. JC6715

    Guide coat for block sanding question

    I am using a high-quality epoxy primer, but a rattle can of Rustoleum auto primer for my guide coat. Do you all think there will be any adhesion or compatibility problems in the low spots where the Rustoleum doesn't get sanded off? Should I lightly sand off the Rustoleum in the low spots...
  12. JC6715

    Gloss body - flat stripe paint question

    Going to be painting the '67 in the next couple weeks here (wish me luck, I'll need it) I'm doing a gloss BC/CC for the majority of the body, but I'm going to have a flat black stripe running down the center of the car using a flat black urethane and a flat urethane clear coat. I'm...
  13. JC6715

    Alternator tests fine, only makes 12.4v on car???

    Been struggling with some charging issues. Newer battery (2 months old), newish alternator, voltage regulator (electronic) and solenoid (all about a year old or so). With a fully charged battery everything is beautiful, starts and runs like a dream. After taking for a 15 minute drive I'll...
  14. JC6715

    8" to 9" break-in question

    I am going to be swapping out the entire drivetrain (old- 289 C4, 8" rear) for new stuff (331, T56, 9" rear). I was hoping to be able to break in the new rear gears in the 9" using the old 289 and C4... EXCEPT, the driveshaft is looking like it might be too long... How much clearance does it...
  15. JC6715

    Mechanical fuel pump lever question

    First time engine builder... Just got a Holley 110gph mechanical fuel pump and the lever/arm that does the pumping is nearly impossible to move up and down by hand. Is this how they are supposed to be or did I get a faulty one from Summit? I would think that the lever should be somewhat easy...
  16. JC6715

    Priming in my garage???

    You guys talked me into priming as I strip the ol Stanger. Correct me if my thinking is wrong: When I am spraying epoxy primer in my garage I don't have to worry a lot about dust and stuff getting into the paint because it's all going to get block sanded anyway... I understand I want it as...
  17. JC6715

    Post-stripping rust prevention

    Is there anything besides primer that could be put on bare metal panels to prevent rust until I can properly epoxy primer my '67? I am hoping for some sort of chemical that could be sprayed on the bare metal to block rust, then cleaned off while prepping for paint... Deal is, my uncle is...
  18. JC6715

    Need to add resistor for point style ignition

    I am in limbo here, fried my Pertronix, and have the old points back in. New engine will be going in in a few months, with a "new" Duraspark dist. How do I add a resistor so i am not constantly blowing the points until the new engine goes in? Old pink resistor wire is long gone... Want to...
  19. JC6715

    Lesson learned with a Pertronix Ignitor II

    If you are running a Pertronix Ignitior electronic ignition, any time you are working on anything electrical where you could potentially cause a short, DICONNECT YOUR BATTERY! I know you are supposed to do that anyway, but how many of us really do? I was monkeying with the ignition switch...
  20. JC6715

    Experience with Restoration Shop brand BC/CC paint?

    I happened upon this website: http://www.tcpglobal.com/restorationshop/rspubprod.aspx (Part of Kustom Shop, TCP Global if that helps at all) Just curious if anyone has used this brand of paint and what feedback they might have. They sell a kit that includes: 1-Gallon Urethane...
Top Bottom
Back
Forums
Menu