Search results

  1. 8

    95-98 Cobra R Front and Saleen Rear Bumper Covers

    $150 for the rear Saleen $200 for the Cobra R cover. This cover does have a crack that will need some help. Not too bad though Both covers have never been painted or put on a car.
  2. 8

    E85

    Yeah I've been gettin the 10% for quite some time now and it seems to run fine. I try and push that on to my friends even though it costs $.02 more then the 87 octane. Figure per tank 1 gallon of renewable cleaner fuel used is better then the imported oil. Don't shoot me for this.. But...
  3. 8

    E85

    E85
  4. 8

    E85

    With the current issues I was wondering if anyone has run this in their cars? I've thought about testing a little bit on top of some regular.
  5. 8

    speaker level?

    I was just wondering what the input level is going into the stock 460 amps? One of mine has died on me and I want to replace it with something else before I leave on my trip tomorrow. I'm assuming the amp on the passenger side rear deck just runs the two 6x8's? in the rear deck?
  6. 8

    Clutch install issues...

    I got my clutch in and tranny back on. The clutch lever has about 2" of play in it. Now when I took it off it was tight. I've taken the trans back off to make sure the throwout bearing was the same as the old one and it is... Any ideas?
  7. 8

    Top Tranny bolts... 98'

    Yeah I already did that... The tranny is as low as it'll go... the top of the motor is hitting the firewall.. That's the reason I think I'll break out the engine hoist tonight and undo the motor mounts. Think I'll be able to get straight on to the bolts with the impact versus going through a...
  8. 8

    Top Tranny bolts... 98'

    considering I've got the exhaust and everything off of it already I think I'd be going backwards attempting to do that and it may not work. If I take the motor mounts out I can get a straight shot to the bolts with the impact.
  9. 8

    Top Tranny bolts... 98'

    Okay what's the trick to getting these damn things out. I've been trying to change my clutch for the last two days and these are the only things holding me up. I've attempted to hit them with an impact through a swivel from the bottom side. I've tried to get to them with a wrench from the top...
  10. 8

    72 Mustang/Cougar Disc Brake spindles

    so I cleaned these up a little bit what do you think?
  11. 8

    Anyone have stock 94-95 front and rear brake assemblies they're looking to sell?

    I've got a set of 94-95 spindles here I'm looking to sell. Shoot me an email [email protected]
  12. 8

    Polished calipers

    I need to polish them one more time but they're looking damn good.
  13. 8

    72 Mustang/Cougar Disc Brake spindles

    I've seen disc brake sets go on ebay for 10x more then that ;)
  14. 8

    72 Mustang/Cougar Disc Brake spindles

    I found a set of these in the shed and just wondered what they were worth?
  15. 8

    Flowmaster American Thunder's or Magnaflow Magnapacks?

    I have the packs on mine with an o/r x and there isn't anything around that sounds similar. That's what I like. It's a little loud at times so I just accelerate through it :shrug:
  16. 8

    Polished calipers

    Actually through the research I've done you shouldn't clear coat them. The paint will not stick to a polished surface. Powdercoating is another story and that's something I'm looking into. I do have some complete. I'll get some pics posted up here this weekend so you all can check them out.
  17. 8

    Polished calipers

    Anyone have these on their ride? I bought a set of the pbrs to polish up to check it out. Might work on a trade out program if anyone is interested when I get done with the first set.
  18. 8

    They dont fit and im pissed

    No... just put jack stands under the frame of the car and lower the rearend down slowly. This will take any pressure off the springs. The quads are not loaded at all.
  19. 8

    Cobra motor install??

    Actually I've found the motor minus the intake for under $1k including shipping.