Search results

  1. 88blowngt

    GOAL: 12.999 on stock motor 5.0 and AOD. Possible?

    I'm looking to do a upr chromeoly k with coilovers with the 14" 130 lb springs in the next few months. I don't understand how your car isn't transferring weight with the better springs up front. Are those moroso springs, drag springs?
  2. 88blowngt

    Rear axle bearing kickin my arse.

    Man it was only a couple of months ago did I have the WORST time getting my passenger side axle bearing out. I heated it up as much as possible and it was still a pain in the rear to get it out with a slide hammer. I ended up fabbing up a little piece of metal and tac welding it to the axle...
  3. 88blowngt

    Looking to snag a Mexican block...opinions?

    What do you guys think of using a mexican block? I read about alot of success over on the turbo 5.0 forums and can see the beefier difference in them when comparing both mexican and stock blocks. Seems like a cheaper middle man to the pricier R302/A4/Dart options for a little extra insurance...
  4. 88blowngt

    I Finally Went to the Track

    Currently my car is a 13.30 car with 3.73s, longtubes, static timing at 30 degrees, a bad clutch setup, slicks and the usual little things. Car weighs 3240 with me and a full tank of gas in it. 60 foots in the 1.89-1.91 range. 13.31 @ 102
  5. 88blowngt

    Has anyone with MGW shifter switched from orange to silver handle?

    Mustang what transmission is your orange handle sitting on? I've been thinkin of an orange handle over my tri ax for my T5 for a while.
  6. 88blowngt

    Anyone Run a T5Z?

    I have one and love it thus far.
  7. 88blowngt

    should it be faster?

    I think 235 rwhp is close to what he can put down. I put down 234/281 with my boltons. Shorties, x pipe, slp lm1 catback, msd dizzy, super conductors, coil, k&n filter, timing at 12 degrees, 91 octane, 3.73s.
  8. 88blowngt

    306 build, help needed

    Last bump
  9. 88blowngt

    306 build, help needed

    Bump, I got an opinion from someone on another forum that the FAC heads are too big to reach my goal and I can get away with the TW 170 heads and the same boost.
  10. 88blowngt

    306 build, help needed

    Hello everyone, Its finally that time to build a motor and I have a base idea of what I want and could use the veterans advice around here to fill in the blanks. I want to build a supercharged 306. I figured starting with an end goal, you pick the parts to meet that goal. Well the goal is to...
  11. 88blowngt

    lightnings, breakfast lunch and dinner

    You're running 13.3s on stock gears?
  12. 88blowngt

    Issues with 60 foot

    I didn't think it had that much to do with it, the difference in 1st gears had crossed my mind though. :nonono:
  13. 88blowngt

    Issues with 60 foot

    After constant practice on and off the track, I think I'm having a clutch issue when it comes to my 60 foot. A friend of mine running a stock T5, stock worn clutch with minor slip and stock motor with boltons like mine is consistently 60 footing in the low 1.7x range. Friends car 87 GT...
  14. 88blowngt

    AC and Smog Delete Kit

    I think I took a good 40 pounds at least off the front. With both pumps removed and what not. I want to weigh it so I'll get around to that and post it tomorrow.
  15. 88blowngt

    AC and Smog Delete Kit

    I realize that but everything counts when I'm out to go as fast as possible on stock motor.
  16. 88blowngt

    AC and Smog Delete Kit

    Looks so much better, hopin to pick up a little power and after my electric fan install its time to hit the track again in March. Minus longtubes, its a full bolton car.
  17. 88blowngt

    Getting fox to run around 8.20s in 1/8th

    Also my mods. BBK Ceramic Shorties, BBK O/R X Pipe, SLP LM1, MSD Pro Billet, MSD Blaster Coil, MSD Super Conductors, Rear Seat Removal, Insulation Removal, Mini-Starter, March U/D Pullies, Steeda Tri-Ax, FRPP 3.73s, MT ET Streets, FRPP AD, RAM HDX, T5-Z
  18. 88blowngt

    Getting fox to run around 8.20s in 1/8th

    Well let's see. My current combination led me to 8.50s in the 1/8th but that was on a horrid 1.91 60 foot. I have some summit brand welds, with skinnies and a 255/60/15 MT ET Street. Its a 27 inch tall tire so its hurting me but I'm about to purchase some ET Drags 26x10 and head back to the...
  19. 88blowngt

    Race Seat Install

    Interested as well.
  20. 88blowngt

    Wondering about a Kenne bell on my 87 GT?

    Not trying to take sides but it might have been better for his point of view if we all answered his questions first and then offered opinions about whats better. Just sayin. :nice:
Top Bottom
Back
Forums
Menu