Search results

I'm swapping out a clutch disc tonight and am trying to save some time and money. Can the transmission can be removed without draining the fluid? Can I just leave the driveshaft yoke in place to stop fluid from pouring out the tailshaft?

I have a 6psi supercharger and timing is currently at 10 degrees. I've set it 12 degrees and it made more power on the dyno but I've since had a leaky head gasket. I'm not sure if it was too much timing or not letting the engine warm up fully before beating on it that caused the leak. I'd like...

Are there any reasons to spend the extra money on the Ford Racing shorties? Can't decide which way to go. Street car, 306, Performer intake and heads, TFS-1 cam, Powerdyne @ 6psi

Recently my starter would continue to run after the key has been turned off. I replaced both the starter and the fender mounted solenoid/relay. It did it again yesterday which resulted in me having to disconnect the cable at the solenoid that runs to the starter because the solenoid started to...

I'm replacing my clutch this weekend. When pulling the tranny, do I unbolt the transmission from the bellhousing or just unbolt the bell housing and remove all at once?

Does the GT40 crate motor come with a flywheel?

I looking for info for a friend of mine and I'm more well versed in 5.0 circles. She just picked up a '04 Mach I (manual transmission) and was looking to install a performance chip. Is there a 'chip' or are just programmers available for the later cars? Is this worth doing for a basically...

Mods are listed in sig. It's time to replace my worn out Auburn unit but I'm not too excited about spending the money to replace it. Can the stock traction lock be used and how is it for power handling and reliability?

My idle is surging and I've cleaned everything; IAC, MAF, and verified TPS voltage at .98v. I haven't checked my timing or fuel pressure but last time it was done I set it to 37psi and 10 degrees. Now... if I unplug a vacuum line anywhere in the system the idle smooths out. What the heII does...

Can a 5.0 be swapped into a 2.3 four banger for street use and still pass smog in California? Has anyone here done this? Edit: Now that I think about it, I'm don't think it would get past the visual inspection. Maybe if I painted 2.3L on the intake.

My car was converted to 5-lug discs all the way around before I bought it. Is the 94-95 spindle the only way to convert to a 5-lug disc? I'm looking into going with a 13" Cobra set up but I'm not sure if I need to start looking for a set of spindle too. Is there an easy way to tell the...

How difficult is it to replace the inner tie rods? $60 for inner tie rods + $?? for boot kits vs. $140 for replacment power rack from Autozone. Or if anyone knows of a better deal on a quick ratio power rack.

GT40 short block Performer Intake & Heads Roller Rockers E303 24 lb injectors JBA Shorties 2-1/2" Exhaust Powerdyne @ 6psi Tremec 3550 3.55 gears 275/40/17's rear Kumho Ecsta MX Daily driver, and I want a clutch that will hold up to the occassional bit of hot rodding and maybe a...

I've just about burned through my rear tires and its time for a new set all the way around. I'm on an extremely limited (read as non-existant) budget. Kumho's sound to be the best daily driver tire for the money. Can anyone give any opinions on the 712's vs. the MX's? The MX's are a bit more but...

I think Ford is purposely leaking information just to get us all worked up in advance. The spy photos of the '05, now this... Awesome commercial! Right click, 'Save As' Ford GT at Thunderhill (3.4MB)

I'm stuck at work and couldn't watch the auction. Can anyone tell me how much the new Shelby GT350SR sold for? The suspense is killing me.