Search results

I am selling my 1989 Mustang GT Vert to feed kids. $ 1500 obo Adult owned its entire life . I have A classic plate on the car that from Pa that I will sign over to new PA owner at notary. Please note Pa requires no photos anymore for classic registrations. The car has receipt binder going...

Ahh just purchased a nice 1989 vert with some mods. The iron heads have the numerals 22 on the right lower front of the head. My old cars had gt and gt40 stamped in the same spot but 22 never saw it before and did a search. Getting back in the mustang saddle after selling my old 347 1987...

Thanks I never would have thought ford would ground the computer in that location. I replaced the wire and added a battery cutoff knob to the negative post. Is there any issues with disconecting the battery with a cut off knob since the computer memory will clear ? The car is my second vehicle...

I am sorry i could not figure out how to upload the picture. ITs the small black wire that attatches onto the battery terminal with the big negative battery cable Why would this ground be important?

Ok guys, On my 1987 mustang gt there is a small black wire that shares a connection to the negative battery terminal what does it do for the car . My 1990 has the same wire. The wire also shares a ground with some sort of two piece snap together connector that is grounded to the chasiss . The...

uhh oh the dog bone is missing. I hope this is what was causing the comotion. Is the primary function of the dog bone to reduce harmonics? I also am getting alot of diffrent opions about aluminium driveshafts. Some people say they need indexed others say no. I am going to try a ford tech line...

I have the ford aluminium driveshaft however it was on the car when i got it no telling how old . I do know that with my old e camed supercharged gt 40 long block I had no bad vibes this summer I had a gps in the car and well clocked in some scary speeds aproaching the limit of z rated tires...

Ok I just had a 347 stroker engine built in August And decided to wind her up a little. However Bad baaaad vibrations are effecting the car mostly aproaching at 3000 rpm in fifth gear around I guess 100mph. The shifter lever vibrates so bad my hand goes numb and the whole car feels as if it's...

Thanks alot of my questions got answered I love the stangnet. I Am going to try the 100 amp hand assembled jegs unit. I am getting the unit for free off an older guy who had it sittin around for awile. heck I should run the powermaster, jegs, and my old 3g in a test and see which one is better...

I am considering getting a 140 amp powermaster one wire alternator. During bad weather and at night time the voltage guage drops big time with my 75 amp unit . Let me know if anyone has tried running this powermaster unit and let me know how it worked out. Previously I installed a 130 amp 3g...

I have destroyed may 2nd t5z behind a 475 horsepower 347 stroker. I would go tremec but autos launch much better at the track and besides the tko is around 1500 bucks. I have donar car with an aod that has been modded in the past to handle 450hp. Has anyone here done this swapp from a t5 to an...

Hey has anyone tried this. I could not find anything searching the forums about this. I would like to get a c4 behind my 347 stroker I just broke in 100 miles and the t5z with only a 1000 miles is howling like an ati procharger or vortech supercharger. Questions I Have Will I need to get the...

These heads kick butt from Ford i am using them on my 347 strocker zheads, zcam, gt40 intake, and this thing got the power . I would say with my 11:0:1 compression ratio i have about 460hp plus and over 400lbs of torque at the flywheel hmm what sti or evo opps bye bye supra I would say the car...

Hey I just got the z304 heads they flow 270 out of box flow numbers kill tfs and other heads damn close to r numbers i ditced the dart head idea for these . The tech guy at ford said those flow numbers are accurate regarding the assembled units, besides canfield was consulted by ford to help...

Hmm ford motorsport high flow z heads anybody running theseM-6049-Z304A* . These heads seem to decent compared to afr or edelbrock TYPICAL AIRFLOW (@ 28'' OF H2O DEPRESSION) WITH 2.02 INTAKE VALVE, 1.60 EXHAUST VALVE AND COMPETITION VALVE JOB LIFT INTAKE FLOW (SCFM) EXHAUST FLOW (SCFM) .050...

The heads I purchased are not drilled for any smog equipment they are dart 195 aluminium heads. The heads are going to be bolted onto a 347 strocker which is not 50 state. Will ditching the smog crap ie smog o matic pump, egr, and the tubing interfere with computer controller? I run a cat less...

I am going to talk with my builder to find out what the cost is for a custom cam . I may get an victor or performer rpm intake that has been ported to match the heads. I heard ported holley are preety good but as is now im working overtime out the rear to pay for this work. Also I was on a...

Are the pro 1 heads equal to the dart sr's or are they a newer design Im asking because i can't find much information on these heads. I hope to make the 11's or low twelves im going to be runnin a 11:1 347 stroker with dart aluminium z303 cam gt40 intake phenolic spacer 65tb t5z no smog junk...

Panhandle performance is shipping me a pair of assembled dart heads they are the 195's and are aluminium. Has anyone run these I kinda got talked into them becuause the guy at panhandle told me they flow 285cfm :rolleyes: intake and are 64 cc chambers which on my stroker will give me 10:9:1...

Ok the engine is going to be topped with dart aluminium pro 1 heads from panhandle performance at a cost of 1395 + I am getting scorpion roller rockers with a lifetime warranty . The engine guy says my compression is going to be 10:9:1 but im ditching the blower. I was told I should be able to...