Search results

For sale is my 1980 Ford Fairmont Station Wagon. The title states it has 27,xxx miles. The interior and exterior are not perfect. There is some small amounts of rust. Most around the windows for some reason. This car came from florida to ohio a few years ago. Underneath is very clean. Frame...

I have a brand new Abaco dbx97 97mm mass air flow sensor. It has never been used. Just been sitting on the shelf. asking $275 they retail for around $390. Thanks!!

Eagle Connecting Rods for small block ford. 331 Stroker rods. They are out of the plastic but like new in box. They have 8740 bolts good for 750 flywheel HP per eagle. 5.400" H-beam forged 4340 connecting rods. Bought new for $375. Selling for $250

I have a set of good used forged stroker pistons for a 331. They are probe 10668-030. They are a dished piston for forced induction. They are for a .030 over engine. They include wrist pins. I have weighed them and they are all the same weight in grams. Asking $250. make me an offer!!! Thanks.

I have a brand new set of AFR 205 cylinder heads. These heads are absolutely perfect. They have had a .005 mill on them to ensure deck flatness. They have never been bolted on an engine. Asking $1650 retails for $1850. Please make offer.

I have an Eagle All forged Rotating Assembly for small block ford. Part # 14014. 331 CI stroker. Has 3.250 stroke crank and 5.400 rods. It has forged 4340 crank and H-beam rods. Everything is brand new. Bought this to do a build and I cannot complete it so I'm selling all parts at a loss. The...

I have an Anderson Ford PMS for sale. I pulled it to go stand alone. My car did low 10's with it. Worked great just got a good deal on a stand alone. It was updated with the newer software. It is wired for a 2-step input. I also have extra pins for the harness if you need to use the extra...

I recently upgraded some things on my car and decided to remove the AFM PMS because I don't really like it. I opted to go with a Quarterhorse from moats and use EEC Editor Software from Paul Booth. Im having issues with the software. Im familiar with other software such as crome,EcTune. Its...

I figured i would get some opinions. I need to upgrade my injectors from #42 to around #96. The #96 are low impedance. #42 are not. Hence a problem. I was running a pms with the #42's and i will be running an a9l with a moates quarterhorse with the #96's. When we tune hondas we usually use low...

I have a dilemma here. Ive maxed out my 255lph in tank. I need to get more fuel this year for my new setup. Here's the situation. I would like to put an A1000 on the car. However, I dont want to use a conventional sump on my tank because I think it ruins the look of my car. Im just not a big fan...

I just put my 86 gt together. i added a qa1 k-member and did a 87-93 gt spindle conversion so i can go 5-lug easily. I want to run the centerline telstars and im havin a bit of trouble. I was going to run a 15x7 with 5 inch b/s. But left turn almost at lock the wheel just touches the control...

i put an art carr built c4 into my 86' me not paying much attention, put the trans in without counting the speedo drive gear teeth on the output shaft. im curious if anyone might be able to give me a range of the tooth counts that c4's came with, i guess if i have to buy a couple gears to get it...

well all i know this sounds like every other post but it may go deeper. than those others. ive finally got everything buttoned up enough to start my new 331 up and get some run time on her. and ive got no fuel pump action. i have done the mass air conversion as my car is an 86. i can jump the...

i got these afr 205 heads, getting ready to bolt on to my stroker. im not for sure if i will need to change pushrod length at all. i would like to have them before final assembly so i can check to make sure valves have enough clearance to the piston. does anyone know what length pushrods i...