Search results

  1. T

    Alternator Not Putting Out

    ok, mech. put new alternator on. It puts out 16 volts with bench test, 12.9 volts when I turn key to on, will put out 13.9 volts when I driving. If I turn heater on, lights on and radio on it will drop to about 12.4 vots. Is this normal, :shrug: :shrug: also got the alternator guage to work...
  2. T

    Alternator Not Putting Out

    Ok sorry it was low amperage. Had the VR changed out at the same time as the Alternator.
  3. T

    Passenger Side back(side) window

    To anyone in North West Fl. (FT. Walton), can you tell me` where to find a regulator and how to install it in a 1968 coupe. Also does anyone in this area know a shop that works on classic Mustang???
  4. T

    Trouble starting, '68 302

    Thanks, Checked the point setting, they were off. She cranks now with just a turn of the key!!! How reliable is the Pertronix?
  5. T

    Trouble starting, '68 302

    :shrug: I have installed new points, coil, condenser, rotor, distributor cap!!!!! It will turn over but will not start. Crank good yesterday morning, but has not cranked since. Whatdo I need to check and/or replace? :bang:
  6. T

    Door latch 68 Coupe

    Thaks!! Thanks for the information on window regulator!!!!
  7. T

    Door latch 68 Coupe

    Need some help and/or information. Need to remove the door latch and window regulatetor on a1968 coupe. Will also be replacing both door panels. Do I need any special tools?
  8. T

    Door Latch

    Have new window regulator for driver side window,also have new door latches for both doors. My question is how do you install all of this??? 1968 Coupe.
  9. T

    New Mustang Club

    Me and two other men at my Church own Classic Mustangs, and I talked to them about starting a Mustang Club. Can anyone in here give me some instuctions on how to go about starting a one?
  10. T

    Looking for members close by!!! (N. FLA.)

    I live in Crestview, work out of Mobile,Al.
  11. T

    DON'T BUY GAS ON MAY 19TH!!

    1. Keep buying your SUV's 2. Don't write or e mail the Congress and free up more drilling (if we don't find more what we have cost more, Supply and demand). The U.S. is very depentant on oil from overseas. But we have as much or more oil here in the US than has been pulled out the ground...
  12. T

    New Seats (New Interior)

    Have a 68 coupe myself and I used Mustang Unlimited.
  13. T

    OT: What does everyone do for a living

    Work for ExxonMobil out of Mobile, Al. Title Operator. Turn 55 this month, so i can retire at anytime. NO, I don't control the price of gas!!!!!
  14. T

    When is a timing chain in need of replacement?

    1. My 2 cents; anytime I see a reply or statement from SuperDave, I am going to read it and learn from what he has to say. 2. I am glad to see someone post how to check the timing chain. I went to pull the water pump off of my 68 when I broke some of the bolts (did not take the time to spray...
  15. T

    Hey Everyone!!

    :hail2: Hey everyone, we have a Celebrity in our mist. Our founder Mike Raburn!!! Check out page 13 in this month issue of Mustang Monthly.
  16. T

    Spark Plugs and Exhaust Manifolds

    Don't know the casing # on manifolds on car (in shop), but order Manifolds from Mustangsunlmited for a '68 w/289/302 engine. Also got new gasket kit and new bolt set for exhaust manifolds. d
  17. T

    Spark Plugs and Exhaust Manifolds

    Have new exhaust manifolds on order, will be here 12/10/03. Had the wrong kind on the car. Have a thin wall 13/16 socket so after installing new exhaust manifolds, problem should be solved. Again, thnaks for everyones help!!!!
  18. T

    new here just saying hello

    Welcome aboard. You will get a lot of advice n here, I have a 1968 Coupe w/302 and folks in here have been alot of help.
  19. T

    Spark Plugs and Exhaust Manifolds

    Thanks crushnut, looks like you are the only one that got the same problem I have. Manifolds should be for 302, at least the man at the Mustang shop I brought them from said they where. Will try taking afile to the manifold and see if that helps.
  20. T

    Spark Plugs and Exhaust Manifolds

    Ok, clear up statement: I need to know if exhaust manifolds will make a different. I have correct size spark plug socket, but it does not fit!!!!!