Search results

  1. 2

    96 Cobra What Blower?

    Well just picked up my third 96 black mustang with a 5spd to finish off the collection lol. Its a 96 cobra with only 12,000 miles. Just going to drive it occasionaly and show it. However, I want to put a blower on it but dont know which one. Debating between Procharger, KB, and Vortech. Leaning...
  2. 2

    Long Tubes and catted shorty X pipe in NJ?

    Exactly...I live in NJ touch the exhaust you fail. That being said iv had longtubes for over two years short h and loudmouth 1's. It can be passed, but not at STATE inspection centers if you know what im saying :rlaugh:
  3. 2

    ET Street on 17x8

    sorry does anyone run a "MT et street bias ply street legal tire" :rlaugh: on a 17x8 rim Im pretty sure the majority of the people would know what im talking about when i say the et street slick. Also, it is recommended on a 9" wide rim just like a 275 bfg but they will fit on a 8" (oh and i...
  4. 2

    ET Street on 17x8

    The only problem is i have to run 17's b/c i have 13" brakes all the way around. Have the bfg drag radials now, but wanted to try an actual slick
  5. 2

    ET Street on 17x8

    I pretty sure some of u guys are running the mickey thompson et street slick(NOT the et street radial) on 17x8 I believe this is the specific one : http://www.jegs.com/webapp/wcs/stores/servlet/CategoryDisplay?lang=-1&catalogId=10002&storeId=10001&categoryId=15715&searchItemId=83853 if...
  6. 2

    10.5's with Baer

    i kind of like the looks with 13" all the way around lol...u guys would too probably if u see them but no one does it seems like
  7. 2

    10.5's with Baer

    It's official 10.5 deep dish bullits dont fit the 13" rear baer brake kit :( They go on a little ways but as the wheel tapers toward the front the calipers hits the side of the wheel. So my question is should or could i buy wheel spacers to bump out the hub mounting surface so the calipers wont...
  8. 2

    VT 1's on headswapped

    Is anyone running the VT 1's in their 96-98 PI swapped stangs? Reason for asking being that we dont have the same dished pistons and was unsure about possible PTV contact. Also, if you had the PI's and switched could you feelthe difference; worth it? Thanks
  9. 2

    Cams after PI Swap

    Well did the PI swap a couple months ago, and the itch to do something else has come up again lol. Would it be worth switching out the PI cams for VT stg 1's or comp cams? I want a nice noticable lope with performance gains. Dont really want to change valve springs, thats why i fiugured these...
  10. 2

    BBK LT's finally on, now some concerns

    I understand people say dont use locktite on header bolts, especially on aluminum heads, but that is just so they will come loose later. I dont plan on taking headers on and off all the time and i dont think other people do either, so the locktite is extra insurance for the bolts. Besides...
  11. 2

    BBK LT's finally on, now some concerns

    Lokar As for the dipstick, u could always get the one from Lokar. Its flexable and would make life alot simplar, if u dont mind paying about $30. Mine however I had to struggle with, but eventually goes in. I also suggest putting in the other header bolts. Try using the ones BBK supplied, it...
  12. 2

    Maintenance to do while doing PI headswap

    definately take the time to clean the carbon off especially since its going to be higher comp....also take compressed air and blow out the water jacket holes there will still be coolent in there that didn come out...messy but worth iimo
  13. 2

    tokico d-specs or bilsteins?

    have d-specs I have had by d-specs for almost a year now. In my opinion they are a very good quality product. However, the only complaint I have is that even on their softest settings the ride is still pretty stiff, I would venture to say harsher then stock. I got them primarily for drag...
  14. 2

    Buying SCT2 tune from? Tune?

    MPH mail order MPH does do mail order tunes. I got one after i did the PI swap and emailed them all my mods. Got the tuner in about 2-1/2 weeks. NOT 1 problem, no pinging or detonation anywhere and definately a seat of your pants difference. Very happy with MPH!!
  15. 2

    Radiators, Fluidyne vs. 03 Cobra

    Have Fluidyne I just bought the fluidyne unit and love it. It is twice as thick as the stock rad. and is a very good quality piece, with all the seam's welded. It fit right into stock location with no problem. And with underdrive pullies, I am running cool (between O and R) on gauge and...
  16. 2

    Tuning After PI Swap

    I just ordered the PI headswap jit for my 96 GT. I am pretty sure its ok to drive it with the stock computer, but know it would be better to uprade. Just woundering what you guys did? I am thinking about gatting a custom burnt diablosport chip. There is really no dyno tuning around me, so that...
  17. 2

    PI or Supercharger

    Simple question: 96 GT Have all basic bolt on's now should I get all the PI stuff, or Kenne Bell kit. I know the price diffrerence, but I want best overall performance, Looking for your guys opinions. Thanks
  18. 2

    Strange or Tokico?

    What do you guys believe is the better strut/shock for everyday use, as well as good adjustment for the dragstrip? Tokico or Strange? Whats your experience with them? Thanks
  19. 2

    Is this a good deal?

    I have a chance to snag a 96 cobra engine with trans wiring harness and computer for $2700. It has 80,000 miles on it, but would rebuild it before I do anything with it. To me it sounds like a good deal. What do you guys think?
  20. 2

    Header bolts loosening?

    Answer to threadlocker I used the stage 8 bolts myself wi th threadlocker (Red-highest strength.) The stage bolts seem hard to start threading in the aluminum heads, and no I was not cross threading. So for assurance I put on threadlocker. With threadlocker there is blue and red. Blue is the...
Top Bottom
Back
Forums
Menu