Search results

  1. Blown331LX

    Installing P600b Procharger FROM SN95 onto Foxbody... Anyone swapped one of these??

    Im getting a nice P600b Procharger setup from my buddys 1995 5.0 and looking at putting it onto my 1991 LX 5.0 which has a brand new 8.5:1 all forged 331 with an F303 cam built for boost... I know I will have to relocate battery to the rear. But only other initial major issue I can think of off...
  2. Blown331LX

    1986 Mustang GT Convertible 5spd - 90k orig miles / Stock - Needs Work but easy resto

    I got this car on a trade for a Jeep Grand Cherokee (That I had over $2800 into) I had a while back, and I have yet to do anything with it. The previous owner drove it 45 minutes to meet me and drive the Jeep back home. It is a mostly bone stock original 1986 GT convertible factory 5 speed with...
  3. Blown331LX

    painting rim thread?

    Get them powdercoated and you wont regret it. Painted wheels look like sh** 9 times out of 10. I got all the wheels done on my Lightning for $250 inside and out, cause they were painted when I bought it and looked terrible... just my two cents...
  4. Blown331LX

    Had it four days and threw a rod!!!

    Id start with a compression test, then a cylinder leak down test to isolate and confrim source. Needless to say youre looking at pulling the engine either for rebuild or replacement. Alao are you sure it was a "brand new" engine 20,000 miles ago or just a "used - new to the vehicle" engine. ?
  5. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    Im still new to all of this but am finding out that C&L calibrations in BE can be very very touchy and not all the same. I currently have the car running and driving but its splotchy at best. I will have a wideband here on Saturday and probably be tuning all the way into next week. Ive relaized...
  6. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    VRISTANG ..... Where can I find a flow chat for specs so I can properly tune my 76mm C&L in Binary Editor?? Ive already been able to set up correct cubic inch, injector flow min and max and increased the idle speed to 850. Thinking I need to have the correct MAF curve next... any other...
  7. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    Ive already managed to find and open that, how do I go about loading it into the PCM on all 8 banks?? I also have the rotary 4 position knob. Id like to load and save 4 tunes into that knob, for now I would just like to have the safe stock tune in there and saved, how to I go about this as...
  8. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    Are these BIN files in Binary Editor? Or an entirely seperate download from Moates.net??? Thanks Chris
  9. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    Thats the exact type of answer I was hopping for, I thought that there may have been something crazy like that going on but so far tech help on this isnt great and there are no good operating tips or instructions I can seem to find anywhere. Any links you know of?? How do I go about loading the...
  10. Blown331LX

    Help w Quarterhorse on 331 & My A9P is no good / What are possible causes of failure?

    My current car is a 1991 LX, original 5.0 automatic car. I bought it not running with a 5 speed and pedals already installed. I got it running then put my 306 in it and got that running till I discovered a broken piston, so now it has a 331. Ever since Ive owned it, there have been running...
  11. Blown331LX

    Parting out 1990 GT / New Jersey 08559

    PM sent.... never heard back from previous message.
  12. Blown331LX

    MINT 1/4 WINDOWS- 150

    Im interested... but need pictures.....
  13. Blown331LX

    Parting out complete '89 GT CHEAP!!!

    Door panels? Or rear hatch panels? what color and how much?
  14. Blown331LX

    Engine Noise in 306.......out of ideas

    Have you ever found a way to turn an engine over by hand with plugs in it any faster than 1 revolution per minute??????? and I dont think anyone could make an injector this loud unless they can make it swing a hammer...
  15. Blown331LX

    Engine Noise in 306.......out of ideas

    So the noise is a rythmic ticking sound that changes with engine rpm. Cold engine start noise is not there and engine runs well, runs for a minute or more and then starts and will get louder. If any of you have ever heard a lifter tick it is the most common sound to this. History on the engine...
  16. Blown331LX

    Fuel pressure issues..... Confused....

    I agree but should the fuel pressure drop even lower when throttle is opened up??? I would think it would have to stay the same or increase because of increase fuel demand and usage..
  17. Blown331LX

    Fuel pressure issues..... Confused....

    Want some input from you guys... Okay so her is the issue.... Im running a BBK 190lph pump feeding into a BBK adjustable regulator. Fuel pressure with engine running and vacuum supply OFF of the regulator is 45 psi. Attach vacuum hose and goes down to 40 psi... when I open the throttle fuel...
  18. Blown331LX

    Parting out 1990 GT / New Jersey 08559

    In need of nice door panels and rear interior trim... price shipped to 27516? Chris