Search results

  1. 9

    UPR BoostMaster Pipe

    I am looking at the UPR BoostMaster Pipe for my Vortech blown 331 and was wondering if anyone else has this piece and how well if fits a 94-95 car vs. an Anderson Power Pipe.
  2. 9

    Roller Rocker Question

    Thank you Juiced_94gt. That was what I was leaning toward, but wanted another opinion. Guess I will have some 1.7 ratio Trick Flows with about 150 miles on them for sale.
  3. 9

    Roller Rocker Question

    I am in the process of installing a new 331 shortblock that my builder installed a Crane Cam. The intake duration is 224 degrees and .542 lift, exhaust is 232 degrees and .563 lift with 1.6 ratio rockers. I have valve springs with a max. of .600. My question is: Is it safe to use my existing...
  4. 9

    Custom chip & PMS possible?

    Thank you Redsnk95 for your help. It is a Series IV. I do have the tps setting to read idle. I believe the start up is around -20% right now. I will watch the O2's more carefully. They seem to be going rich / lean fairly quickly, but I will watch closer. I have played with the air...
  5. 9

    Custom chip & PMS possible?

    Well, one problem I have is that I don't have a wideband, so I am only going by what the stock ones are showing. Here is what it's doing. When it is cold, it will start and idle fine at around 740rpm. Once it starts to warm up it will start to wondering from 950rpm to 650rpm. The main...
  6. 9

    Custom chip & PMS possible?

    I have a quick question. I installed a Vortech SQ, Trickflow heads, Performer intake, 80mm Pro-M, 70mm BBK, 42 lbs injectors on my otherwise stock shortblock. I purchased a Anderson PMS to tune it, but I am fighting getting it to idle and run well. I have been looking up past threads and have...
  7. 9

    got trouble codes with upgrades

    Thanks for the tip! I will try that out and hope it take care of it. Did you experience in surging around while cruising around 2,000rpm? I went in and added fuel @ 2,000 which seemed to help, but it's still there.
  8. 9

    got trouble codes with upgrades

    I have installed an Anderson PMS and PMAS 80mm MAF with 42# injectors along with a Vortech V-2 and TFS heads (stock shortblock and cam) I now have code 157 (MAF below min voltage) and 124 (TPS higher voltage than expected). I have tried resetting the throttle and has a decent idle @ 750-800...
  9. 9

    Installed PMS, etc, and now got t. codes

    I just installed an Anderson PMS, Pro-M 80mm calibrated for my 42lbs. injectors, TFS heads, Vortech V-2 and I'm fighting problems. I set up the initial program that Anderson Ford gave me for my car. I can't get it to idle below 1,000rpm (I have stock shortblock and stock cam) and it idles...
  10. 9

    the darn white smoke

    I installed a Vortech earlier this year. The first time out, I stepped into it a bit and it knocked like crazy so I got back out quickly. Brought it home and it was dropping a cylinder on the driver's side. I backed it back out the next day it here came the white smoke out that side. I took...
  11. 9

    AFR 185's on stock short block?

    Is anyone running Airflow Research 185's on a stock short block? I have read that there may be piston clearance problems with the 2.02 valves. I just installed a Vortech V-2 and took out a head gasket :nonono: on my otherwise stock longblock and want to install a 347 soon, but until then while...
  12. 9

    Will Lightning MAF with PMS?

    Thank you for your help everyone. :hail2: I guess I didn't research enough before I bought the Lightning MAF and the PMS. Anyway, I have a new 90mm Lightning MAF and pigtail for our cars for sale if anyone is interested.:D
  13. 9

    Will Lightning MAF with PMS?

    I just finished installing a Vortech S-Trim, 42lbs. injectors and 90MM Lightning MAF on mostly stock engine other than throttle body and Performer intake. I just got my PMS and faxed the sheet to AFMS to get the intial tune. I got back a sheet from Anderson saying that my MAF wont work and I...
  14. 9

    Vortech boost control needed with PMS?

    I am installing a Vortech S-Trim and I have decided to get a PMS to go with this install. Should I still install the ignition/boost control that came with the Vortech or is this just redundent with what I can do with the PMS. I already have a MSD 6AL and I'm running out of room under the hood...
  15. 9

    Vortech install questions.

    I am installing an S trim on my car. The motor is stock except for a Performer intake, BBK throttle body, headers and exhaust. I decided to install 42lbs. injectors and 90mm Lightning MAF along with the Vortech. My questions are: I will not need the FMU, correct? Should I use the T-Rex pump...
  16. 9

    missing / hesitating

    Thanks dstanggt50! That was it! I replaced the maf today and its running like a champ. Thanks again.
  17. 9

    missing / hesitating

    These forums have been great! I have gone through the not starting(stator) and the popping frontend(tighten the cross brace) easliy with past forums. The problem I currently have is the car randomly missing out. It seems most noticable at lower rpms going down the highway and underload. The...