Search results

As the title says, I'm looking for a set of yellow top injectors. These are going on my 02 expedition, not looking to spend a lot. I gave away my set from my fox like 15years ago... In League City, Tx

Ok I have a 02 GT that i swapped an 03 mach 1 engine into using the original GT computer and wiring harness. I had the car tuned with an sct x3. On the third dyno pull during tuning the sct tuner crapped out, so my tuner gave me a new sct tuner. Because of this i lost my "stock" GT tune and now...

Ok, When i bought my 2002 GT it had some probs. One of the first i noticed was the drivers side rear banjo bolt was almost all the way out. Fluid was leaking everywhere. I trailered her home, and tightened it up. I bled the brakes and MC with a one man bleeder kit till there was all new fluid...

Just picked up some new Moser 31 spline axles and a cobra trac-lock :D I need to get some new wheel studs to go with the mosers and want to get a good set of 3 in. studs for them. I'm not for sure but i think i have picked out the right size and thread (1/2-20 RH in.) and press in...

Well I picked up a used SLP o/r X to try out, so I installed it last night along with a new clutch cable. This is on my 2002 GT with Mach1 motor. Today when i drove the car I realized I needed to adjust the cable a little. So up the car goes on jackstands. I'm under the car with it running...

2002 GT I'm trying to find a clunk noise coming from the front end. It only seems to do it at low speeds like pulling into my driveway. It will do it in forward or reverse motion, But only when i brake hard at low speeds. I've searched all over the intraweb and seems that this is a common...

Old Today, 03:57 PM #1 MATT87GT Junior Member MATT87GT's Avatar Join Date: Dec 2007 Location: League City, Texas Posts: 11 Icon5 Tapping sound when cold I've done several searches, and still can't answer my problem so here goes nothing... A little back ground. I just...

Anybody tell me what size, thread pitch bolt/nut I might need for my passenger side h-pipe to stock header??? The nut seems to have come loose and fallen off :D and I'm hoping that the cause of the huge exhaust leak I'm hearing. 2004 GT SOHC Thanks Ahead of time :flag:

Ok long one here, So i first put my combo together completely myself (with the help of a friend lol). Cam in dot to dot. Heads on. Cobra intake. It ran like ****, had bad vacuum problems, no trhottle response etc etc... Pulled it all apart. Took the heads in and had them checked out. All...

Got the car running tonight with the new setup, BUT it has a vacuum leak somewhere :bang: It'll start and run, It pulls about 10 in of vacuum at first (@ 800 rpm), and will pull 20 (@ 2000 rpm). But it will slowly lose vacuum. It only takes between 2-5 minutes and the vacuum will zero out...

Well i got the heads off tonight, and the first thing i noticed is the pistons say .030 right in the middle. I go check my spare block which is a stock 89 block and the pistons say ford on them. Bust out the dial caliper and sure enough the cylender bore is 4.030 . The pistons do not...

1. When checking P2V should i use NO head gasket, an old head gasket, the head gasket i plan to use??? 2. If the pistons need to be notched can it be done with everything still in the motor, USING A DREMEL??? :SNSign:

My instructions got lost when the wifey took my truck one night and i'm about to go have everything installed in the rear end . I looked on the moser website but couldn't find anything. If anyone knows a link to installing c-clip elims in an 8.8 or a link to the moser instructons for...

Ok so i was thinking today if there was anything else i needed to go with my head swap. Then i realized if I'm changing the timing chain I'll have to pull off the balancer anyway so why not put on a new one while i'm at it. Looked at some prices and an SFI approved balancer from FRPP is...

Adding AFR 165's, 1.7 RR's to my current combo. How much HP/TQ do you guys think it will ADD or Put down to the wheels with my current combo??? One more question: I have everything to put the heads on. I also have 31 spline moser axles with C-clip elims, A new 31 spline T-lock...

Picked up the new 357w today for R.Barns, and we got started assembling the rest of the motor but ran into some problems. 1st problem: The dizzy won't sit flush. We are using an ARP oil pump shaft and an MSD dizzy for the 351w. Do we cut/shave down the dizzy or the arp shaft...

Tommorrow i'm going to FRPP to buy: 8.8 rebulid kit M-4210-C FMS 8.8 Girdle M-4033-G1 Gasket Set M-6003-A50 Roller lifters M-6500-R302 Timing chain kit M-6268-A302 GT40 upper to lower gasket And this is some of what i have so far :D I also have stock length hardened...

Going to be swapping the heads soon FINALLY. Got a sweet deal on some barely used afr 165's with 1.7 rr's and stock length hardened pushrods. I know, I know, I am going to need to check p2v. But i've never done that before and I need a complete write up on how to do it and what stuff i will...

Got my baby back on the road today!!! The trans has been in the shop for 2 months now :nonono: . So it's got a new KC clutch, rebuilt trans to "z" specs, resurfaced flywheel, new tob and pilot bearing. Took it for a easy spin around the block and everything seems to be good. How many...

For a 306 combo, How much compression could i get away with running 93 octane? Setup would be something like... fresh 306 Stock crank Stock Rods New forged pistons New rings New bearings E-cam Cobra Intake with lower port matched to heads (or gasket) New world senior heads (gasket...