Search results

I was looking around my 94 Cobra and found a black box under the passenger seat. the only thing written on it is Ford Motorsports. It has adjustment dials for A/F ratio and the rev limiter. Are these still made? Ive never seen one of these before.

I have a whine in my drivetrain. I thought it was the T5, so I swapped in another T5 (have no history on it). I still hear the whine. Sound increases when on the gas and when completely off the gas in the upper RPMs. Happens in all gears. Still whines when clutch is out and in neutral. TOB...

So im in the middle of doing a fox T5 swap into my 94 Cobra. I have hit a major issue. I'm trying to bolt up the cross member, but when I lift the tranny enough to line the bolts up, the shifter hits the floorpan! Has anyone here ACTUALLY done this swap? Is there a way to fill the trans...

I've done this before and IIRC I used a pilot bearing for a 83' Ranger 2wd with a 2.2L diesel engine. Well I ordered that pilot bearing, and took my 5.0 bearing out of the crank. Wouldn't you know, the swap bearing has the correct I.D. for the 2.3 t5, but the O.D. is to small for my crank (my...

I'm looking at buying a 94 cobra that needs a driver side fender, headlight, and bumper cover. I've found all these parts, but they are for GT/LX cars. What else is needed to swap the headlights and bumper cover? I've read they are GT/LX and Cobra specific.

I'm go'in to a ladies house to change the brakes on her 2000 Stang. I need to know exactly what tools to take with me, as I have only messed with 79-95 cars before. I read during a search that I will need a 15MM and 12MM socket, as well as the tool to retract the piston. Is that all that is...

I just bought another Mustang with 1k miles on a rebuild. The car has NO power at all! Will barely spin the tires. If you get on it, it wont rev, and sorta hesitates/misses. If you rev it in neutral, it wont go above 3 or 4k RPM, like it has a rev limiter. I've checked the TPS, key on...

I've got a stock engine that after running it hard for about an hour just cut out on me going down the road. There is no spark at all coming from the coil. What could cause this?

I just hooked a 2g alt up in a carb'd car. The alt isn't charging. Am I supposed to put a switched 12v to the lt grn/red wire that originally ran to the cluster lamp? Seems I remember reading that the alt wouldn't charge without a 12v signal coming in on that wire.

Just wondering of anyone out there has used this intake with new fuel rails? I have UPR rails. They won't work with a stock 5.0 intake (just found out the hard way!). I want to get rid of the stock fuel tank ASAP so I can cut out the floor in the trunk, and mount the fuel cell, as well...

I have the 4 banger tranny, and a V8 bellhousing. Can I swap the clutch fork and everything in/on the bellhousing from the 4cyl to the V8 bellhousing? I already have a V8 clutch set, flywheel, TOB, and conversion pilot bearing. I wouldn't be asking, but I don't have the 4 cyl bell...

I have never considered "trashing" my car up with the decals I get when I purcahse parts, but I have been thinking about adding "Built, Not Bought" to the rear glass on my coupe. I've had my car striped down to the bare chassis multiple times, and the only thing that is original to the car is...

I was talking to my friends mother today and it turns out she was a mechanic for 20 years. She told me that if I held a dollar bill to the tail pipe and it was blown away, I had a healthy engine, and if it was sucking in, I had a poor running engine.... WTF?!?! Now i've heard of...

I am about to rewire my car, but I need a diagram for the engine harness since it connects to the body harness. I am trying to keep the computer harness factory, but rewire the rest of the car since all I will need is the tail lights, head lights, dome light, horn, and ignition. I have seen...

I haven't drove my car in a few weeks. I went to drive it yesterday and found out I have lost my keys for it, no biggie, I started to drill out the tumbler. I was wrong, I can't get it out! Since this is a drag oriented car, I want a toggled hot and push button start system. Does...

I have some Steeda CC plates that I ordered for my 89 car... I see that some places split the years up around 90 or 91, does anyone know if it is ok to use them on my 93 car?

Will a 300 I6 bellhousing from a F150 work? I have heard that they have the same bolt pattern and will bolt up. Will the clutch fork work also?

I just pulled a 5.0 out of an 88 Thunderbird. I got to tearing it down, and it has a roller cam, but it does not have the valve reliefs shaped as eyebrows of an HO. It does have a "dish" in the center of the piston, that dips down about a 1/16th of an inch. I forgot to look @ the heads to get...

Has anyone ever converted their fox to a remote TFI setup like the 94-95's? I am going with a EFI 460 and it seems like it may be easier to use a dizzy with a remote TFI than modify the dizzy.

Let me start off in saying that the mods in my sig are on another stang. This one is also a 5 speed 4 banger. I have done ALOT of weight reductions on it. I am also running a 275 Nitto DR on the back. I can not hook at all! It just wants to spin! I can nail it from a dead stop and it...