Mustang & Ford How-To Articles...........

[Cyclone]

Hi All, Just thought you might want to check out some of these very informative Magazine Articles that I have done for Jim Smart & Miles Cook, Just click on the Links below to view each article that you wish to view.........

9th Annual Mustang & Ford Day, and Suspension Clinic
http://www.fly-ford.com/Suspension _Alignment_Clinic_March_2004.pdf

How-To-Install Sub-Frame Connectors, By Miles Cook
http://www.fly-ford.com/MM0105-How_To_Install_Subframe_Connectors.html

How-To-Install Export Brace & Monte Carlo Bar, By Miles Cook
http://www.fly-ford.com/MM0105-How_To_Install_an_Export_Brace_and_a_Monte_Carlo_Bar.html

How-To-Rock & Roll Wheel Guide, By Jim Smart
http://www.fly-ford.com/MF0804-Rock_N_Roll_Wheel_Guide.html

How-To-Trim Coil Springs & Check Alignment, By Miles Cook
http://www.fly-ford.com/MM0804-Trim_Coil_Springs_and_Check_Alignment.html

Alignment Science, By Jim Smart
http://www.fly-ford.com/MustangFords0404-AlignmentScience.html

Exhaust Article “Sounds Right” By Jim Smart & Marlon Mitchell
http://www.fly-ford.com/MustangFords0404-SoundsRight.html

How-To-Install Grant Steering Wheel, By Jim Smart
http://www.fly-ford.com/MM0604-Install_a_Grant_Steering_Wheel.html

How-To-Replace a 1971-73 Dash Pad, By Jim Smart
http://www.fly-ford.com/MM0204-Replace_Dashpad.html

How-To-Install Sequential Tail Lights, By Jim Smart
http://www.fly-ford.com/MM0404-Install_Sequential_Taillights.html

Understanding Alignment, By Jim Smart
http://www.fly-ford.com/MF0303-Understanding_Alignment.html

How-To-Install a JME Instrument Gage Panel, By Jim Smart & Jeff Fischbach
http://www.fly-ford.com/MF0203-Panel_Discussion.html

How-To-Alignment Basics, By Jim Smart
http://www.fly-ford.com/MM0105-How_To_Alignment_Basics.html

What You Need To Know About Vintage Mustang & Ford Alignments, By Jim Smart
http://www.fly-ford.com/MustangFords0800.html

2005 Ford Mustang Display with FoMoCo
http://www.fly-ford.com/2005_Mustang_Display.html

 

[19simmons65]

Great post! Resources like this are always needed by newbie's like myself.

 

[Cyclone]

Here is a link to view pictures of my Mustang....
http://www.allmustangandfordclub.com/MembersRide-MarlonMitchell.html

 

[jerry S]

Here is a link to view pictures of my Mustang....
http://www.allmustangandfordclub.com/MembersRide-MarlonMitchell.html

Very nicely done. Is that 302 stroked? If not, 400 hp from a NA 302 is quite an achievement. What bracket you are using to mount that MSD Blaster Coil on the cylinder head?

 

[66moneypit]

There should be a dedicated "how-to links" section IMHO. This would be a great start for one of those pages.... If there is one already and I have been missing it...then I apologize in advance.

 

[monk302]

Cyclone,

Thanks for the links. I am sure they will help alot of people.

 

[84convertablegt]

nice

 

[Grant65]

Just an FYI, the page on installing the JME instrument cluster is missing a page. It goes from page 41 (removing the original cluster) right to page 43 (now that your connections are soldered...).

Overal though, a lot of good information...

Grant

 

[Max Power]

Cyclone,

What do you mean by "I have done"?

 

[jerry S]

Cyclone,

What do you mean by "I have done"?

I am guessing that Cyclone is Marlon Mitchel, the owner of Marlo's Frame and Alignment and that these are articles on jobs he did that were written by either Miles Cook or Jim Smart for MM.