Pro flow same as Pro M

Discussion in '94-95 5.0 Tuning' started by Dagz, Aug 20, 2009.

  1. Dagz New Member

    Member Since:
    Dec 3, 2005
    Message Count:
    173
    Likes Received:
    0
    Trophy Points:
    0
    Hello again. Just working on tweecer my car here. I am unsure of my maf transfer. I have a 80mm Pro flow calb. for 42's that came off a lightning. I have heard the pro flow is the same as pro m, is this true? Can I use the pro m maf transfer? Or where can I find the maf trasfer for the pro flow.

    Thanks again
    Dagz, Aug 20, 2009
    #1

  2. pirotec354 New Member

    Member Since:
    Aug 29, 2008
    Message Count:
    129
    Likes Received:
    0
    Trophy Points:
    0
    Pro m and Pmas are the same I believe. I dont think there is any relation with pro flow.
    pirotec354, Aug 20, 2009
    #2

  3. tealstang67 New Member

    Member Since:
    May 20, 2009
    Message Count:
    47
    Likes Received:
    0
    Trophy Points:
    0
    I thought pro m bought pro flow years ago. Maybe i am mistaken.
    tealstang67, Aug 21, 2009
    #3

  4. Chythar Active Member

    Member Since:
    Aug 26, 2004
    Message Count:
    1,850
    Likes Received:
    1
    Trophy Points:
    48
    From what I heard, Pro-M went out of business a while ago. Some of the employees from Pro-M bought Pro-M's equipment at auction and started up PMAS. So essentially, PMAS is the heart of the old Pro-M.

    According to one tidbit I just read, one of the engineers at the old Pro-M decided to make his own sensors under the old Pro-M name, don't know if that's real or not.
    Chythar, Aug 21, 2009
    #4

  5. tealstang67 New Member

    Member Since:
    May 20, 2009
    Message Count:
    47
    Likes Received:
    0
    Trophy Points:
    0
    Maybe that is what i read. To much reading. :D
    tealstang67, Aug 21, 2009
    #5

  6. Dagz New Member

    Member Since:
    Dec 3, 2005
    Message Count:
    173
    Likes Received:
    0
    Trophy Points:
    0
    Thanks guys I read some similar information. I also read something about pro flow tied in with pro m but haven't found out anything forsure. In the tweecer software start guide (calcon/caledit) it makes reference to proflow and how easy it is to find maf transfers for them. I'm having a hard time finding almost anything on them.

    The maf I have is an 80 mm draw through pro flow. It's calb for 42's and off a lighting as stated above. I know obvious it is going to be calib. different then say a fox maf or our maf but I am having a hard time finding info.

    I talked to a tuner and he says to set my injector scalars to match the 42's and use a stock maf transfer and increase it by 75%. Sound like this is a way to go?

    Thanks again
    Dagz, Aug 21, 2009
    #6

  7. tealstang67 New Member

    Member Since:
    May 20, 2009
    Message Count:
    47
    Likes Received:
    0
    Trophy Points:
    0
    i would try the pro-m xfer that coinsides with yours meter And fine tune from there. I had a pro flow cal'd for 30# inj at one time and i used the pro-m xfer and edited it as needed. If i remember correctly it was only like 6 percent off. Just my .02 cents though. Good luck:D
    tealstang67, Aug 21, 2009
    #7

  8. Dagz New Member

    Member Since:
    Dec 3, 2005
    Message Count:
    173
    Likes Received:
    0
    Trophy Points:
    0
    I was thinking the same thing. I think it's worth a try. If not ill go with what the tuner said but seems like the pro m would be a better starting point to me
    Dagz, Aug 21, 2009
    #8

Share This Page