Search results

  1. J

    Diagnose my CEL codes please

    I've installed a new 347 with 10.4:1 compression. Edelbrock RPM heads, cobra intake, 24lb injectors, proM maf, 70mm tb, 1 5/8 headers, 2.5 inch exhaust, and trickflows stage 2 cam. I started the motor and set timing to 14. It continuously stalls. I raised fuel pressure to 44 with the vaccum...
  2. J

    What should this combo make?

    Just wondering what kind of HP this combo might make. Its a 347 with forged (probe) pistons and rods, cast scat crank, Edelbrock Performer RPM heads with 1.9/1.6 valves, trickflow stage 1 cam (for now) cobra intake, 1.6 stud rr's, 75mm tb, 24lb injectors and maf. with shorty headers, 2.5in...
  3. J

    351w -> 393

    Does the 351w block need to be bored to make 393ci's? I know I need a new rotating assembly including a 3.850 stroke crankshaft, but does the bore change? I'm trying to decide between buying a bare block or the whole shortblock. If no boring is necassary I'll buy a bare block and the right...
  4. J

    19lb injectors enough for this setup...?

    I recently installed Gt40p heads, Trickflow Stage 1 cam and spring kit, Ford racing "P" headers. Plus the car already had an intake, Cobra upper and lower, 19lb injectors and maf, UPR X pipe, Flowmasters (2.25 i think) BBK Throttle body, Efan, adj fpr, Full MSD ignition, and a NOS brand wet...
  5. J

    Spinning pushrods

    I installed a set of 1.6 for racing roller rockers along with gt40p heads and a tfs1 cam. I made sure I could torque down the rocker bolt in less than one full rotation of the torque wrench when I installed them. I spun the pushrod until it came tight, then torqued in less than one full turn...
  6. J

    Gt40p's and E303 cam

    Im about to install a set up GT40p heads. I'm currently running an E303 cam, I have no idea what heads are in the car, but their cast iron and suck, so im not sure of the valve train and wouldnt be supprised if the springs dont match the cams lift. (new car) I believe the E cam has a .495...
  7. J

    Which Holley brand NOS jet size's = 100 shot?

    I cant seem to get any help over in the POWER ADDER section, so I'll post my questions here. I have a handful of jets and a wet NOS brand kit. I'm trying to get the correct jets for a 100 shot. I've been researching and found this nitrous calculator that helps you figure your jetting out...
  8. J

    How To Request: 300whp na on a 306

    I just picked up a nice little 93 coupe. See link for pics... 93 Mustang RED Coupe Original 5.0 Notch BLACK INTERIOR First I plan to replace the LCA bushings(because there are NONE), do a compression test, and lower the shot to 100. After that I want to add some power off the spray. I...
  9. J

    Shopping for heads. Who/What is SBF?

    Just browsing around on ebay for a new set of heads when I came across these...
  10. J

    Name this Carb (pics)

    I found 8050B on the side, but cant find that on Holley's site. Anyone know the size?
  11. J

    Picked up an 85 that was "Built for spray"

    I just picked up a little project car. Its an 85 GT with no seats, interior, or ac. The previous owner says it has: 302 bored 30 over to 306. no info on the piston/rods but he said it was built for spray. Trickflow stage 1 cam Ported stock heads w/GT40 1.6 roller rockers Cobra Trans...
Top Bottom
Back
Forums
Menu