Search results

  1. F

    Tx Locals, Brazoria

    I'm a NY native that just relocated to southern Houston area. What are the emissions requirements? what I viewed on TX inspections site was very vague... Refers to a visual inspection in one part and a sniffer in another... Which one? both? I have an after market exhaust that past westchester...
  2. F

    cross drilled rotors cut in North NJ or South western NY

    I'm looking to find a place that will resurface/cut cross drilled or slotted rotors in Bergen county NJ or Rockland/Orange/Westchester county NY. Alot of places won't do it as they fear it'll wreck the bits on the lathe machines. If any one has had success getting them resurfaced in that area...
  3. F

    2000 Cobra R front Pads

    I'm installing a brembo 2000 cobra R front brake set up on a 2003 Cobra. I know the size/part is the same as a standard 13" cobra rotor, but the pads are different. Does any one know the ford part # for the brembo pads? Or does any one know the dodge part # for the same pads? I do know that...
  4. F

    Maximum Motorsports Adjustible rear swaybar

    MM Adj rear sway bar, for 79-04 solid axle. Not IRS. 3/4 inch, bolt in kit. New in box. Was purchased for a 2003 GT but never installed. asking $ 250 or best offer.
  5. F

    aluminum driveshaft 99-04

    Aluminum driveshaft out of 2003 GT, used. excellent condition. Comes with 1330 slip yoke and ujoints. Was used behind a stock tremec 3650. Ford Racing Performance Parts - [Part Details] asking $150 make me an offer. located in 10992
  6. F

    TA rear end girdle/cover 8.8

    New in box, never installed. TA performance 8.8" high strength differential girdle/cover. Forged aluminum. This will clear an aftermarket panhard bar on a 1999-2004 mustang gt. Has bearing pre load bolts, complete kit. make me an offer. Ford Girdles | TAPerformance.com asking $ 100
  7. F

    99-04 forged axles, 8.8 31 spline new in box

    New in box, never installed. Alloy USA forged axels for 8.8", 31 spline. Will fit 1999-2004 ford mustang, not cobra. Paid over $200, sold car never installed. Comes with seals seals, bearings and studs. Make me an offer. asking $150 Part # 12187 AlloyUSA - GM Ford Dodge Rear Axle Kits...
  8. F

    rear end shop in orange county NY

    Does any one know of a good shop to assemble a rear in orange county NY? I already have all the parts was goin to do this myself but project repeatedly delayed by home responsiblities. 31 spline Differential, gears, axels, TA cover, aluminum drive shaft and weld tubes. I live in...
  9. F

    FE engine/block Id

    This guy nearby has an FE engine he claims is a 427. How do I confirm this if the engine is assembled and missing the engine tag? I believe the part #'s aren't visible from the outside. If the engine is in pieces (which it may be) where are: the casting #'s on the block? (I read somewhere...
  10. F

    toploader interchange

    can a toploader for an FE engine (390/427/428) bolt up in place behind a 429/460? Using a 429 bellhousing/clustch setup. are the bolt patterns and tranny input length the same? 69-73 429 toploaders are tough to find. thanks in advance.
  11. F

    toploader ID

    Can some one point me to an internet resource for Toploader ID #'s. I have the interchange manual, but I have noticed that it lacks some #'s. I need a resouce that has part #'s for cases and tail sections in addtion to tag #'s. I have seen several transmissions thus far that have inacurate...
  12. F

    super T-10 into 67 cougar/mustang

    I tried doing a sear on this here, at corral, and mercurycougar forums to no avail... This is for a 67 cougar, currently with a 289. Can I mate a GM super T-10 to a ford small or big block? the reason I ask this is I can get one cheap, that I know is rebuilt and good to go. But I don't...
  13. F

    backspacing on bullit rims

    can someone tell me what the backspacing is on the 17x8 stock bullit rims form 2000-2004? I'm interested to see if they would fit on a late 60's cougar or mustang. with a 5 by 4.5 bolt pattern same as the SN95's. thanks
  14. F

    Part # ABS rings

    Can some one tell me what the part # is for the rear ABS rings on a 2003 GT? thanks in advance.
  15. F

    Valve tick?

    My '03 Gt with 27,000 on it is making what sounds like intermittent valve ticking. Starts about 30 seconds to one minute after car has been started and can be heard on and off until the car is at full operating temp. I already checked the torque on all my plugs and they're all >13 ft/lbs...
  16. F

    forged axles

    I need help selecting forged axles for and '03 GT with a 31 spline diff. I see that FRPP, strange, moser and superior all make forged 31 spline axels for my car. Whats the difference between each, I've also noticed that the prices are all almost equal from lookin at various venders, all are...
  17. F

    stainless steel brake lines

    Is there any point/benefit in using these on the rear calipers? Also can somone point in the direction of a good install article for putting rear cobra calipers/rotors on a GT? thanks in advance
  18. F

    installing cobra rear brakes

    To those of you who have installed a rear cobra disc brake set up on a 99-04GT: (this is for a 2003 GT if that makes a difference) I am upgrading my rearend components this winter, and I ran across this article on modulardepot: http://www.modulardepot.com/?show=articlesdet&aid=54 Which was...
  19. F

    diff cover

    Does anyone know of a differential cover for the 8.8 that has recessed bolts for preloading the bearings (bolts don't stick out beyond the ridge on the cover)? I have a MM PHB and the diff. covers with exposed/raised bearing loading bolts may hit the PHB crossbrace during bump travel.
  20. F

    building a budget rear

    Correct me if I'm wrong...but late model (not sure what years) explorers had a 31 spline tracklok 8.8 with 3.73 gearing, I'm pretty sure the V8's did but I am not sure about the V6's. So this should be a direct replacement upgrade for a mustang when combined with 31 spline axles. If this is...
Top Bottom
Back
Forums
Menu