Search results

  1. S

    Billet Steel Flywheel Suggestions

    I am at the point where my TKO600 is out of the car and going to be headed to get rebuilt(ujoint let loose on the freeway and smacked the transmission cracking the case and bell). While that is being done, I am going to replace the rear main and pilot bearing. I figure my stock flywheel is going...
  2. S

    TKO 600 Repair

    Hello, Anybody know of a place that will repair a TKO 600. Buying a new one for 2200 is a bit much. My housing/case is cracked as far as I can see so I know I need at least that... Kevin
  3. S

    Opinions on a Foxinator

    Hello, Recently my Ujoint let loose on my driveshaft. One of the caps is MIA and well... Not sure how but my TKO600 case is cracked pretty good and I am an unhappy camper. I am at a crossroads and was debating by either buying another TKO which will run me about 3k when everything is said and...
  4. S

    Possible driveshaft length issue

    Hello. Little history on the car... I have a cobra IRS and a TKO600(about an inch shorter than a T5). With that said, my driveshaft let loose on me while I was on the freeway... My x pipe is a tad beat up but it probably saved me if anything... Anyways I got a great deal on an 03 cobra AL...
  5. S

    WTS FMS 3.55 gears NIB 150 Shipped

    I bought these before I did my 04 cobra IRS swap(includes 3.55s) so they are up for grabs now. PM me if you are interested. Thank you. Kevin
  6. S

    WTS TFS stage 1 cam w/10 miles on it 140 shipped.

    Hello. Just watching this thing sit in the garage. TFS stage 1 with 10 miles on it tops. Broke it in, drove it to the smog station and was turned away for a smog test. Too lopey for their taste out her in CA. The cam is missing the timing gear dowel but other than that it is near new. PM me if...
  7. S

    O2 sensor thread size.

    The bung on my xpipe has a couple messed up threads. What is the thread size so I can chase them before putting in my new O2. Thanks. Kevin
  8. S

    power steering hardline part #

    I managed to crimp the hardline that comes outo of the middle of the steering rack while doing my engine mounts. Anybody know of the part number? I was looking on late model resto but they didn't seem to have it... Thanks for the help. Kevin
  9. S

    IRS spring orientation

    Hello, I am swapping an IRS into my fox and all the online instructions say to mark the stock location and install your aftermarket springs. Well I just need to tell me wich way the pigtail points or a pic would be awesome. Thank you. Kevin
  10. S

    Carbon fiber cowl hood on a fox

    I was curious of anybody had any pictures of a CF cowl hood on a fox. I would greatly appreciate it. I am looking at a VIS but cannot find one. Please save the rice comments... I am half chinese... not that I take offense, its just that I don't care if its rice or not. If I don't like the...
  11. S

    which and where to find an 03/04 rear driveshaft flange

    Hello guys. I posted this in 5.0 section but probably the wrong place to begin with. I am looking for the rear driveshaft flange that fits an 30/04 cobra IRS. This is one of the couple things I need left to get started on this project and don't know what type it is other than its larger than my...
  12. S

    03 cobra IRS... which companion flange adapter

    I am only short a couple things for this IRS swap and apparently ford uses a different companion flange adapter on the 03/04 driveshaft. Is this the right one? http://www.currieenterprises.com/CEStore/productsre.aspx?id=1250 Thanks Kevin
  13. S

    Spindle suggestions cosidering 03 cobra IRS installed

    I am in the process of installing a 03/04 cobra irs in the rear and in doing so the whole brake system is going too. If I were to use the fox length rear axles or even the pre 99 sn95 rear I would look for some 94/95 spindles. Here is my question... Considering that the cobra IRS is fairly wider...
  14. S

    Little help with IRS bracket part numbers

    I have long contemplated(3 months hehe) an 03/04 IRS swap for my fox and this past weekend I was able to pick one up for 460 minus brakes, shocks.... and the rear brackets... Does anybody know the part number or where I can find the brackets? I have exhausted google, ebay and craigslist and...
  15. S

    Thought you guys would get a kick out of this

    In the worse case save you some money if you thought this would work. http://www.rx7club.com/forum/showthread.php?t=141942&page=1&pp=15 Kevin
  16. S

    Differences for 87-90 and 91-93 saleen kits

    Hello Guys, I am looking at buying a Fox Saleen kit that is suppose to have come off a real saleen and I was curious how I can tell the difference for which year car it is for. I know the front fenders are different between 87-90 and 91-93 and assumed that the kit would differ too. The current...
  17. S

    Rod Knock?

    Hello guys, This isn't for me but for a friend of mine. I know its hard to diagnose a rod knock over the internet but I believe my friend's 2k GT has it. The only thing is that it comes and goes which is really odd to me. The car shudders and its doing the knocking thing then it pretends to be...
  18. S

    Just spun the 5.0 onto a medium/island what damage should I look for.

    Well to start off my Friday I spun my 5.0 and landed it on an island. What damage should I look for. This was all at about 10-15 MPH around a left hand turn. So far the passenger fender ate it into the curb benind the front tire on the median and I took out a small dead tree which put a wave in...
  19. S

    Anybody have the new MGW TKO500/600 shifter?

    I had a MGW for my T5 and absolutely loved it. The stock shifter for the TKO is pretty poor... I mean I would go back to my stock T5 shifter... I was going to get a Pro 5.0 but them I checked MGW's site on the off chance they made one for the 500/600 series and they do now. Any feedback on this...
  20. S

    Anybody looking for 5 lug Roush wheels found them on clearance

    Just keeping an eye out for you guys. Kar Kraft has 18x8 early Roush wheels for 75 bucks a pop. I dunno if its a typo but it might be worth giving them a call for that price. Not sure if they will fit and I am not associated with Kar Kraft so don't bother flaming me. Just helping with people's 5...
Top Bottom
Back
Forums
Menu