Search results

  1. B

    UPR boostmaster bypass valve

    So i just installed the plastic UPR boostmaster pipe but am having problems with the bypass valve that i rigged up. i used a 90 degree elbow from home depot and attached one side to the pipe with some PVC glue and the other side clamped to the hose from the bottom of the bypass valve. it worked...
  2. B

    Surging / bucking at low speed / RPM

    Having an issue with my car surging / bucking at low speed / RPM. If I’m slowly driving through a parking lot, the car will begin to surge and buck and gradually get worse and more violent until I push in the clutch and let the idle catch back up again. Then it will be ok for a few seconds until...
  3. B

    Supercharged fuel, timing, gap, etc...settings

    Nice, thanks. Hey blueblazes, the air/fuel....is that at idle or WOT?
  4. B

    Air/Fuel and Vaccum advise

    Im going to run an air fuel meter and vacuum gauge to better understand why my car is not happy at idle and WOT. What should a 302 with a blower, heads and E cam usually show for for vacuum? What about the air fuel at idle and W.O.T? Thanks in advance.
  5. B

    Supercharged fuel, timing, gap, etc...settings

    Still having idle issues. Seems like there is a vacuum leak but i have checked all hoses.... I think. Im going to run an air fuel meter and vacuum gauge. What does a motor with a blower, heads and E cam usually show for for vacuum? What about the air fuel at W.O.T? 12:1?
  6. B

    87-93 door belt moldings ORIGINAL FORD!!!

    the belts are super easy, just open your door, and look where the molding ends and there is a screw. Once Screw is removed, the bolt molding just slides out.
  7. B

    Supercharged fuel, timing, gap, etc...settings

    Gotcha, thanks again! I think i'll stick with .035 as it seems to be a good and safe set up.
  8. B

    Supercharged fuel, timing, gap, etc...settings

    Hey guys, thanks for the feedback..... I have a 6AL that came with the s-trim, so you think i can go larger gap than a .035? If i wasn't selling the car i would lose the 24# and FMU for a good tune in a second. I just want the car to run good or better for sale.
  9. B

    Supercharged fuel, timing, gap, etc...settings

    Looking for some advice on performance settings on my 91’ stang. It have a 302, Vortech s-trim running the stock 8 lbs of boost and FMU and 24# injectors. Car also has edelbrock heads and Vortech upper and lower manifolds. Looking on recommendations for fuel pressure, timing, plug gap and any...
  10. B

    Looking for the 4 lug 17" Saleen rims??

    Tied them but when i asked they didn't have any for the 17" wheels. I ended up ordering one from Speedline in the UK. I just don't have a matching decal. I'll check with them and see if they have any. Thanks for your help!!
  11. B

    Supercharged Plug & Gap Advice

    Can you guys advise me on the recommended plug and gap for a vortech supercharged stang with Edelbrock performer heads. Thanks in advance.
  12. B

    Convertable door belt molding removal

    Does anyone know how to remove the door belt molding on a fox body vert?? Mine are all weathered and need to be replaced or painted. Either way I'd like to take them off 1st if its not too involved.
  13. B

    87-93 door belt moldings ORIGINAL FORD!!!

    Can you tell me how you remove and install them 1st??
  14. B

    17" speedline saleen wheel cap

    Well the guy on the phone said i could not buy from him as im not a dealer. PM sent.
  15. B

    17" speedline saleen wheel cap

    So i called them and they made me feel like i was asking for a glass hammer. They had no idea what was was talking about. Did you have any luck??
  16. B

    17" speedline saleen wheel cap

    wow dude.... Thanks let me know. You would be a life saver
  17. B

    Inner Fender plate for intake tube

    I have a powerflex intake tube for my supercharger on my 91 vert and i need to get a plate that mounts to the inner fender for the tube to go into. i know its for aesthetics but can this be bought separately as what i have did not come with one??
  18. B

    Cold Air Kits

    I have a powerflex intake tube for my supercharger on my 91 vert and i need to get a plate that mounts to the inner fender for the tube to go into. i know its for aesthetics but can this be bought separately as what i have did not come with one??
  19. B

    Advise on making engine bay look better

    So i have a 91' blown stang and am just tired of the engine compartment looking like it does. compared to my SRT Charger the engine compartment looks....well just sloppy. What are some ways to simplify the look and make it cleaner in overall appearance. here is a photo of what i have now...