Search results

finally the weather, time and cash flow stars have aligned, I managed to get the AJE K Member installed, and I have installed the SN95 lower control arms with 5 lug brakes & shocks in my 80 model. The springs were a bit of a bugger to get in, however the overall job went well. it's obvious the...

I am wanting to change the oil pan gasket with out pulling the engine I also have to replace the timing cover gasket and replace a leaking rear main seal. I was wondering if I were to remove the clutch & flywheel, and replace the rear main seal, then lower or remove the steering rack if I...

just put in an AJE cross member and my rag joint come up about 3/4 to an inch short at the mounting bolt. original rag joint was not stressed, frame not bent. put original k-member back in, all seems normal, put AJE back in, still short. any ideas is this normal?? also noted was when I tried to...

I finally got an AJE k-member and a road race brace kit, and now it's time to get it in labor day weekend. I was wondering if a set of 97 lca's would work on my 80 model. The bushings on the 97 are in better condition than my 80 models bushings. but most importantly I'm thinking that the track...

i just put a new temp guage in the dash of a 65 mustang and it worked ok for about 15 minutes, then smoke came out of it. i'm pretty sure the two pins in the back where the wires go were not touching any metal, could this be a bad guage or did i mess up the instalation?? i have also replaced...

wanting to know if anyone has done an 8.8 swap. i want the 8.8 axle with posi and disc set-up. i've got fox and sn95 rear ends to choose from. i see there is a difference so far as drive yokes and spring perches. 8.8 diff are going to be around forever and offer the discs brakes as stock, and...

i have a 93 GT , and i want to fit the 88 5 spd GT tilt steering collumn and cluster. i didnt know for sure if the collumn would fit as it looks diferent where it mounts up at the upper end and the cluster wiring looks diiferent also.(manual /auto) i cant seem to find a wiring diagram form the...

Gotta question about fitting a 4.6 liter sn95 k-member to a fox. I am wanting to drop a 4.6 in my car, but I am uncertain as to the procedure, some people say you have to cut it off in the back and elongate the rear holes, some say the bushings for the lower control arms have to be reversed...

i am getting ready to fit the 4.6 into the 80 model, i have a 93 dash in it at the moment. i noticed the hook-ups for the ac evaporator are bigtime different, will the sn 97 evaporator core & heater core fit into a 93 plenum? if not will the 97 plenum fit into the 93 dash? this is worth sorting...

getting ready to install the 4.6 in the 80 model, id like to know if the stock exhaust manifolds will fit, and can i use the stock steering shaft. will most likely be using the k.member from the 97 mustang, or should i use the AJE tubular style. my main concern at the moment is the exhaust...

got a 90 mustang, 5.0 5spd, i want to put an oem mini starter on it, is there a special starter to fit for the manual transmissions, or just fit the same starter as the automatics, its a good mod do, its a lot quieter, and i think it has more torque with less of an amp draw.

i am slowly picking-up the parts for upgrading the rear brakes to discs on a 93 mustang 8.8. i've got the backing plates, anti moan brackets, mounting brakets, rotors, i just need the calipers and axles and parking brake cables. i noted someone said the that gran marquis calipers would fit, but...

has anyone put a 94 & up dash and console in thier fox body. i think it would look cool, and i'd really like a cup holder. i can but assume it to be easier to obtain a complete car to have the frt to rear loom. i really dont mind the electrical part, i just wondered if they would physically...

hey fella's, i'm new to the site, actually, i joined today. i've already completed my front brake upgrade using the spindles, shocks, ball joints calipers, spindles etc from a 2000 mustang v6. i am currently using a 95 cobra m/cyl and 95 gt booster, still have the drums in the rear at the...