Search results

So the previous did a battery relocation to the trunk and it looks like a crappy job. I have been having hard starts since I got it and have been wondering if this could cause it. Hopefully pics show up

hey guys, looking for some new heads for my 306 mustang..not looking to drop a grand on heads as this motor wont be in the car for that long. it has an f-cam with 1.6 svo roller rockers. what are nice reasonably priced heads that will make this alphabet cam shine.

my efi is all jacked up in my car cause someone added mass air to a speed density car and now wires are all over the place and it runs like balls. so im going carb and my question is can you use the stock electric pump for the carb? i was told yes and you just need a fuel pressure regulator and...

so i put a new battery in the car and started it up and everything works..next morning the thing is as dead as a doornail. put a multi meter to it and its at 6 volts.. so i did an amp draw test and its pulling 1.06 amps. And im pretty sure it should be like .50 or somewhere around there right? I...

i drove the car yesterday and then parked it..went to start it today and it dies. It will start for a few seconds then no matter how much gas you give it to keep it going it dies. then it will just crank and crank and crank and if you wait a minute it will start again then die. Pulled codes and...

i put the jumper wire to the 2nd pin on connector and to the solo wire. then the test light from positive terminal to 2nd connector on the bottom. then i turn the key on and the test light stays lit. does not flash or anything. what am i doing wrong?

Ive been trying to chace down a no idle cold start and i noticed a plug not connected to anything and i dont see the other end anywhere. The car has no ac or smog and it has a h/c/

Ok, first off i know about the checklist and all that but i cant follow diagrams and lists if my life depended on it. so i bought a notch that has a 306, holley heads, cam, trick flow intake, intake spacer, egr spacer, CAI, 30# injectors, smog delete and its an 87 with mass air conversion. the...

Im about to buy a notch of my buddy and the only thing holding me back is that the right rear sits close to 3-4 inches lower than the left..all other corners of the car sit the perfect height. It was a former drag car so my concern is that its just been launched so hard that it twisted bad. But...

I recently bought a 93 2.3 mustang with 89k on it. Has a huge skip. I checked the entire ignition system and its all good. Im going to check vacuum lines then after that idk where to look. Do these engines have this kind of problem?? It sounds and shakes like its running on 2 cylinders and can...

Bought a 93 lx 4cyl auto. 90k original miles. Needs a new hatch and a few rust spots on the floor. My plan id a v8 swap with a 6 speed. But the best part is. Bought it for 400 bucks!

Im looking for a roller and found one with everything i want, but the catch is it has been hit in the front and may have frame damage. Is this fixable? I know LMR sells apron and fender replacements.. Heres the ad. I dont know if it will work tho...

who the hell sells the damn things??? every site ive gone on only sell the right side and not the left.Who sells both??????????

Ok, i know i dont have a fox anymore but the ppl in this section give the quickest response..so on my 97 cobra with a stage 2 clutch it shifts perfectly just cruising..but when u push the clutch in all the way and slam it into the next gear it grinds badly...anyone know what can cause this?

i got a 97 cobra on trade for my fox. when i drive it and slow down to like 1,500 2k rpm the car revs back up as if i downshifted but i didnt. Is this an IMRC problem? And what exactly does it do?

traded my fox for a 97 cobra.. list: stock dohc engine(158k) cold air intake new msd coils and wires new MM cc plates underdrive pullies sct tuner with tune rebuilt tranny stage 2 clutch wideband steeda short shifter extra head liner and dash bassani catless x-pipe into magnaflows dumped. mach...

http://philadelphia.craigslist.org/cto/2935202940.html

i was adjusting my clutch via firewall adjuster and it fell out and i cant get it back in. Is there a special way to twist it back bck in or am i just handicapped.

my dad has 74 corvette 350 4-speed and he told me that when he lets off the clutch the pedal pulsates rapidly and is hesitant. Any clue what this is? Also says he thinks the problem is in the rear end and he wont let me touch the car so i cant really decribe what its doing

i'm kinda gettin sick of my bullitts and want something new. Im wondering if there are any nice rims for under 500 bucks. i love draglites, prostars, and saleens but there out of my range.