Search results

  1. jeffnoel

    P0457 Code even after replacing cap

    Got a P0455 code awhile back and then the check gas cap light came on. I purchased a new cap and cleared the code and gas cap light with my Predator. I little while later the check gas cap light came back on. Then after driving a couple hundred more miles the SES light came on. I pulled the...
  2. jeffnoel

    CEL came on got a couple codes

    P0171 & P0174 System 2 lean banks 1 & 2. The light came on yesterday while the wife was driving her 02 GT. Plugged in the Predator this morning and these are the codes it's showing. I have done a search and looked around for vac leaks couldn't find anything obvious, but I did notice the soft...
  3. jeffnoel

    Duraspark distributors

    I heard the vacuum advance was adjustable on the Duraspark distributor. Is that true, if so which way does one turn the allen wrench to either advance or retard the vacuum advance?
  4. jeffnoel

    Valvetrain noise or detonation?

    I istalled a set of rebuilt E7s from a 90GT on my 78 302, they have the same valve size bit a 64cc chamber compared to the 69cc chambers of my 78 heads. Both heads use pedestal mount rockers. I picked up a set of Crane 1.7 rollers and installed them along with the E7s and a new Edelbrock...
  5. jeffnoel

    Valve clatter could it be timing?

    OK some of you know I recently fired up my engine and broke in a new cam. Engine sounds great in the garage under no load but when driving it I'm getting some noise from the valvetrain (I think) when accelerating. Here is what I did to the engine: 1978 302 shortblock with 41K miles...
  6. jeffnoel

    ProComp Electronic parts ???

    Anyone have any experience with the magnetic trigger distributors by ProComp?
  7. jeffnoel

    New exhaust for the Cobra

    DynoMax side exit mufflers with 2.25" pipe and 3.5" tips.:D Click on picture for video with sound.
  8. jeffnoel

    She's alive !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    Well it's been about II years since I've had the Cobra on the road. Over this past winter I made a few change to the factory 302 engine with 41K on the bottom end. Here's the list; 8-qt oil pan. hi-vol oil pump and CM shaft, Edelbrock Performer cam, Crane Energizer 1.7 ratio roller rockers...
  9. jeffnoel

    Problems encountered while attempting to break-in a new cam

    I tried starting the Mustang after the winter mods and it won't start. I have gas, 5 gallons added to the recently cleaned and sealed gas tank. Fuel filers are clean and I have spark, I checked by pulling the #1 plug and grounding it to verify spark at the plug. I prefilled the fuel bowls in the...
  10. jeffnoel

    Local Carshow Pics

    These are from the Northside Christian Church carshow yesterday. Carshow Photo Album
  11. jeffnoel

    Water Pump Pulley

    I'm looking at installing just the water pump pulley from a set of UD pulleys. Brothers Performance sells the set of Polished billet pulleys pictured below and I just want to install the one for the water pump, is there any reason that would cause a problem? By the way I do have a Fluidyne...
  12. jeffnoel

    Spark Plug pics

    I just replaced the plugs on my 02 GT. The engine is stock with 83,690 miles on it. I replaced the stock plugs with some Autolite 764s that I bought like a year ago and just never got around to changing them until now. New plugs are gapped at .054 old plugs came out at about .060+ on average...
  13. jeffnoel

    MSD COPs

    Has anyone tried these yet? Just wondering if they are worthwhile when you start building power. Any thoughts???
  14. jeffnoel

    Purple Racing intake

    Anybody have any info on this intake? eBay link to Purple Racing Intake
  15. jeffnoel

    How to fill Holley fuel bowls

    Like the title says. I'm getting ready to break-in a new cam and would like to minimize cranking before the engine fires up. Do I just pour a measured amount of gas down the vent tubes? Should I add gas to both the primary and secondary bowls?
  16. jeffnoel

    Fresno Veterans Day Parade pics and vidoe

    Here is a link to my photo album with pics and video from this years Fresno Veterans Day Parade. There are 2 mov videos one small about 4.4Meg shot by sticking my camera out the window during the parade. The other is 75Meg of the entire Mustang portion of the parade as it was broadcast on the...
  17. jeffnoel

    Roush 3rd Brake light decals

    Does anyone make custom decals for the 3rd brake light on S281 spoilers?
  18. jeffnoel

    Mustangs Plus Fall Display Pics

    I still have about 40-50 cars to add but will get it updated later today. Photo Album Link
  19. jeffnoel

    Mustangs Plus Fall Display Pics

    I still have about 40-50 cars to add but will get it updated later today. Photo Album Link
  20. jeffnoel

    Veteran's Day Parade in Fresno

    Guess what - This year the Veteran's Parade is going to be on SATURDAY, November 11. Isn't this great. This is the first time its been on a Saturday as long as i can remember. Soooooooo those of us who usually work on Veteran's Day have no excuse not to participate. Pass along this...