Search results

  1. JamesBaumann

    Tuning Question

    Does anybody know if I can use the ford IDS to tune my combo? 331 Edelbrock heads E303 24lb injectors etc. Any help would be great.
  2. JamesBaumann

    Hypothetical HP Q

    Thanks again. Yes, I definitely plan to have it tuned some way or another, and yes, an AFPR will be something that will definitely be part of it.
  3. JamesBaumann

    Hypothetical HP Q

    Thanks for the input. Obviously I will do as much as I can before I need it, but who knows how much that will be. I agree that the cam is a little small for the stroker, I just got a great deal on it and decided that it would be a good cam for the street, which is what the car will see 99% of...
  4. JamesBaumann

    Hypothetical HP Q

    Hey guys, just looking for some opinions here on my combo. This past May my stock 5.0L bit it :notnice: I am just finishing putting together my longblock which is a 331 stroker bottom end with FRPP E-303 cam, and edelbrock performer 6037 heads. My question to you guys is what would you...
  5. JamesBaumann

    Clutch is dead, how much ?

    Flat rate time on the clutch is about 4.5hrs. You should probably get a new rear main seal as well.
  6. JamesBaumann

    2.02" or 1.90" for street stroker

    Ok. That being said, would there much advantage by going to a 2.02" head?
  7. JamesBaumann

    2.02" or 1.90" for street stroker

    Well, I am still undecided on what heads I will go with. But that cam with 1.7 RR should be lifting about .530" which I think will be enough for what I'm after.
  8. JamesBaumann

    2.02" or 1.90" for street stroker

    Im using Keith Black Hypereutectic pistons. They will clear a valve 2.05" with .600" lift. (Advertised)
  9. JamesBaumann

    2.02" or 1.90" valve for street stroker

    Thanks for the input. I already have the E303, so I will surely be using that. I plan to be using the edelbrock performer intake because it seems to have a street friendly rpm range. You make a pretty good point about how I wont really need a huge intake valve if I am using a mild cam and...
  10. JamesBaumann

    2.02" or 1.90" valve for street stroker

    Hey guys, I know that this has been covered before, but I am just looking for a couple opinions directed more to my question. I have just put together a 331 stroker shortblock with the FRPP E303 cam. I'll likely be using a set of 1.7 RR to give me approximately .530" lift. This car will be...
  11. JamesBaumann

    2.02" or 1.90" for street stroker

    Hey guys, I know that this has been covered before, but I am just looking for a couple opinions directed more to my question. I have just put together a 331 stroker shortblock with the FRPP E303 cam. I'll likely be using a set of 1.7 RR to give me approximately .530" lift. This car will be...
  12. JamesBaumann

    Engine Removal

    Actually, its just a stock motor with 80k miles. I'm fairly easy on it, dont know what happened.
  13. JamesBaumann

    Engine Removal

    Thanks for the input. By the way, I am sure that the motor is blown up. From underneath looking up you can see a giant hole in the timing cover where you can see the main bearing spun and the crank shifted about an inch to the front of the car. The timing chain is broken and laying in a ball...
  14. JamesBaumann

    Engine Removal

    I ran a search and looked through the tech sticky but couldnt really find what I was looking for. Does anybody happen to have a tech article for engine removal on a 94GT. I seemingly blew mine up today, so I figured a tech article might make the removal process of the motor a little more...
  15. JamesBaumann

    Quick stereo question

    Hey, thats great. Thanks very much for the help Chythar.
  16. JamesBaumann

    Quick stereo question

    I ran a search but couldnt find any answers to my question. I have a 94GT with the base (non-mach) stereo. I am wiring up my own stereo with my own 4 channel amp to power the speakers. My question to you guys is, where are the stock amplifiers located? If there are any. It seems all of the info...
  17. JamesBaumann

    pressure plate question

    nevermind, im dumb. Thanks anyway.
  18. JamesBaumann

    pressure plate question

    Hey guys, I did a search and found nothing. I am currently trying to pull my pressure plate off and there are three what appear to be retaining tabs holding it in. Can anybody give me any help on how to remove these tabs and take off the pressure plate? Thanks for any help guys.
  19. JamesBaumann

    Drop spindles

    I will probably go with springs, but I am just interested in shopping around to see what is out there. Drop spindles also seem like a cool idea because you dont sacrifice as much ride quality.
  20. JamesBaumann

    Drop spindles

    Does anybody know of anywhere where a guy can get a set of drop spindles for a 94GT? Thanks for any help guys.