Search results

  1. S

    adj fuel pres reg + fmu for blower?

    i ran 12#'s 42 inlectors 80mm mass air and an power pipe with no tune and i took it to the dyno and the af was pretty much dead nuts 12:1 little rich down low but up top perfect. I also had a lot of bas timing in the car as well.
  2. S

    possible fried computer?

    hey guys i let my buddy use my car and it died so he jumped it. He hooked the battery cables up backwards and now the car doesn't wanna run. Its a 5spd with and auto computer in it and its pulling a tot(transmission oil temp) code which it never pulled before. Also its saying low voltage to the...
  3. S

    SC + T5 + 400HP=?

    i have 475 at the wheels and a stock t5. I have about 30 or some track passes and who knows how many miles beating on it on the street. Still holds up just fine. NO grinding or poping out of gear and no howling from the tranny in any gear.
  4. S

    What is the NH law on emissions?

    nope i beleive there is no sniffer test for you still just a plane old inspection. Dont hold me to it because i know a guy who helps me out with my sticker on my 90 because of my dumps.
  5. S

    no oil pressure HELP!!!

    Yup time for a new bottom end if its not toast yet. Same thing happened to me had to get a whole new block, crank, and pistons because my crank was scored. It was easier than putting a new crank in and having everything balanced. I would stop driving it imediatly and check your bearings. so you...
  6. S

    Rear Suspension Question

    Hey guys i currently have a set of south side lift bars on my car. Should i remove them if im going to be putting lakewood 50/50's with a drag spring in there?
  7. S

    Head Torque Question

    Hey guys i currently have a set of edelbrock heads that are fire ringed and have lockwire head gaskets. Edelbrock says to torque them down to 70-80ft lbs. Do you think this is enough considering im going to be running 12-15lbs of boost and possibly a small shot like 40 or so of nitrous?
  8. S

    S/C Question

    Hey guys I was looking into a ysi but it says clockwise rotation only. What does this mean will it still work on my car a 90 5.0?
  9. S

    What Lug Nuts?

    Hey guys i recently purchased a a set of weld drag lights for my car. I never got any lug nuts with them from the guy i bought them off. What size and kind of lug nuts do i need for a 90 5.0 4lug? Thanks.
  10. S

    ONLY 280HP OUT OF THIS COMBO!!!

    1987 lx t top stock bottom end .030, high volume oil pump, FTI cam, AFR 165, 1.6 rr, TMoss ported cobra intake, #30 injectors, 255lph fuel pump, 75mm tb, 80mm MAF, a/c delete, sub-frame connectors, 4.30's and much more. This is just my 2 cents. I think your throtle body is to big i have a...
  11. S

    T/B Problem

    Hey guys i just purchased a new accu-fab throttle body last year. And its starting to seize up. When i first start up the car and hit the gas its hard like its stuck but then it frees up. My previous throttle body did the same thing. Could this be from running the coolant through it?
  12. S

    Help Car shut off wont start

    hey guys just rebuilt my motor. Drove it about 1/4 mile and it just shut off and the tach went dead. Theres coolant leakin out. (i think from the head) I was wondering if maybe the heads werent torqued down enough because the heads are fire ringed but i am not using fire ringed head gaskets...
  13. S

    New Motor Mounts Now Have Problem

    the mounts are side specific and there on the right ones. The driveshaft sits about an 1.5 from where it used to be because i can see some shiny input shaft. I got the mounts from pep boys for a 5.0. Ill see if they have different ones.
  14. S

    New Motor Mounts Now Have Problem

    HEy guys i took the motor out of my car to rebuild it when we put it back in with the new motor mounts the motor sits about 1.5-2 inches closer to the nose of the car and i cant get the fan in. Any ideas to what might cause this? Maybe i reversed the mounting plates the motor sits on?
  15. S

    Eibach Drag Spring Install

    Hey guys whats the best way to install the eibach drag springs in the front. By droping the A-arm is doesn't seem to bee enough room and they are pretty hard to compress with some sort of ratchet strap. Will spring compressor do the trick?
  16. S

    rim and tire question

    Hey guys i ended up gettin a set of weld wheels 15x3.5 and 15x10 for a real good price. Anyways the front runners have tires on them already and the rears need new tires. can i put the 26x10.5x15's i have now on my ten holes onto the 15x10's or will they be to small?
  17. S

    A- Trim

    the a-trim is an entry level blower its not made to make high boost. I think they make like 5-6#'s of boost maybe more if you can put a diff pulley on it. Even so if you put an a-trim on i dont know how well the flow numbers are on them. So i dont see more than 300 and maybe 325-350 at the the...
  18. S

    Supercharger Questions

    Look at my sig. Its pretty much what you guys have just i have the s-trim. Theres been no port work to any of my parts or block. Also i didn't get a tune and on the dyno my A/F ration was pretty much perfect. The car went 12.3 @120 in the 1/4 mile. That was with worse than stock suspension...
  19. S

    need help which supercharger

    look at my sig for my set up. But i have the s-trim runs about 12-13lbs stock 302 block 42's lbers, 255 intank fuel pump. No problems here. I dont run a FMU either and i dont have a tune. I put the car on the dyno ready to do a chip to adjust fuel curves and the car was pretty much perfect...
  20. S

    South Side Lift Bars and 50/50's?

    Hey guys i currently have a set of south side lift bars in my car. I also have a set of lakewood 50/50's kickin around. If i put the 50/50's in should i remove the lift bars or keep them in. let me know thanks.