mustang

My friend has a 1996 Mustang GT that he wants to LS swap (he's a sinner) later this summer, and I want to do a V8 swap in my car which is a 1998 Mustang V6. He said he'd sell it to me for $850, but I was wondering if I also needed to buy his transmission from him or if the two cars use the same...

Listed is a 3" x 3" Dr. Gas Exhaust Crossover kit with Summit header collector, I intended to use this on a 1966 Ford Mustang (with headers). This should work on most 64.5-73 V8 Mustangs. actually since it is a cut and weld to fit solution it should fit most applications using a 3" X-pipe or...

I'm rebuilding my engine and when I got the block back from the shop, they had removed the counter shaft and synchronizer to clean out the block. There is a bearing that sits next to the gear on the counter shaft and one end of the bearing is tapered. Does anyone know if the tapered end should...

View: https://youtu.be/j24DDd9dX7I

I just recently found a listing for a 1970 Mustang Coupe (I believe it's the coupe model) and I've always wanted to drive a classic muscle car, but it's in pretty rough shape. The author of the post said it runs but the interior is rusty and I assume the trunk is worse. This doesn't bother me...

Hey guys I bought a new lock for the trunk on my 89 foxbody but I have no idea how to install it.. when I bought the car it had no lock in the back so I didn’t have to take it apart. I’m confused on the lock extension and where it goes on the lock itself. Any one have an idea how to fix this...

Hello, The 1968 Mustang my dad has been working on for the past 10 years, in New Mexico, is almost to the finish line! The car should be coming to me, in California, mid-March. Currently, what has been ordered and what is being worked on is... New tires Remove the V8 springs in the front and...

Hello, I have a 08 mustang v6 and believe it has a rear end problem. I put it up on the lift today and I think the rear diff mount bushings are worn. Could this cause the rear end to dance side to side? I also think my drivers side trailing arm is a little worn as well. Please help!!!

Hello guys I need help with my 91 mustang GT, recently replaced the lower & upper intake and had to remove the heads to get 2 broken bolts drilled out . Reassembled and whenever I start the car it jumps straight to redline and stats there .If I disconnect the intake tube it idles around...

Is it possible to replace my 2000 Mustang v6's steering wheel with a more vintage one? Perhaps a 1965 steering wheel.

I have the stock audio for 1997 mustang GT with a after market head unit. I was driving the other night and out of no where I lost all bass in every speaker. I tried to change the head unit but that didn't work. I have no idea what can make me lose all my bass in every speaker.

Looking for a good condition Mustang Cobra IRS unit to swap into my fox hatch. Would prefer a 2003-2004 unit. Can be 100% stock or fully built. Have cash in hand and willing to make a couple hundred mile trip if necessary. I'm located in SE PA. The complete stock 8.8 axle in my '89 is up for...

Hey guys I have a 98 gt with pretty good paint, few chips and scratches but very minor, I was wondering exactly what buffing does. I wanna make it look really pretty but Idk exactly what buffing does and if it will hurt my paint where the chips are.

Hello I recently put a new clutch kit, (clutch, bearings, and pressure plate) and flywheel, I also put in a new clutch form because it was broken in my 98gt and beforehand the clutch was SUPER stiff. After I swapped all of that it was like butter and over time it became super stiff again. Any tips??

Hello everyone. I came today with something odd. I own a 2003 v6 mustang (manual) and as i work on it something that shows constantly is the idea of tuning the car too a higher compression ratio to use high octane gas. This would give the car a little bit more of punch; however, there is always...

Hey everyone got a pretty stock 98 gt and was wondering how much hp I could expect from bbk long tubes and a bbk off-road h pipe? Especially given that the stock midpipe has like 4 or 6 cats

was doing some detailing on my engine bay when I noticed a possible leak coming from under my boss 302 manifold. Had a couple of my buddies look at it and told me not to worry about it..... Thought I’d get more opinions. The spot is dry. Not a very big spot but nonetheless... I can’t explain...

hey guys, so at the moment I have the factory 302 with 80,000 miles on the mustang. love the car but its to slow. So after this deployment I want to throw a a stroked 351w to 408 CID. looking for someone who's done the same thing as me and what they recommend. heres what I want: 1. Keeping the...

Hi, is there a way to make a mustang 5.0 1990-93 engine harness a3m computer work with a 89 dash harness? Please let me know if there's anyway to make this work other than buying a whole 89 engine harness, thanks!

Cold start, regular driving, aggressive driving, WOT, etc... Let me know what you guys think! View: https://www.youtube.com/watch?v=UbwIf7Y_TGg