Search results

  1. M

    Mr.Hawver's MS3X Tuning Thread

    Hey there, I have a MS3X project that is running decently well, but I'm hoping to get a little assistance to smooth things out and optimize the tune. My biggest concerns are the lean start (pegging out my WBO2s, despite increasing the After Start Enrichment significantly) and the bucking from...
  2. M

    BBK Header Fitment

    Hey there, I am trying to shoehorn some BBK equal lengths from a Fox into my 95, but I am having a one problem. Before you say it, I know, equal lengths are horrible ideas, but I got them really, really cheap... so I'm giving them a shot. Anyhoo, I've got the header bolted up on the...
  3. M

    Carfax Pretty Please!!

    I'm looking at a 350z for a bit of a fun car so I don't put so many miles on the Stang. Could someone run a Carfax report for the VIN: JN1BZ34E07M550567 Thanks for your help!
  4. M

    Need Help Diagnosing Wailing

    Hello all, I have a wailing coming from the back of the engine/bellhousing/tranny area. Before you say it, it isn't the throw out bearing, as I have disconnected the clutch cable so the TOB isn't touching the pressure plate, because that is what I initially thought too. It all started...
  5. M

    Battery Draw

    How much current does it take to run our cars with everything on (heater/AC on high, high beams, radio on, etc.)? I'm trying to size the cable I'm running up to the fuse box appropriately without being overkill for my battery relocation. Thanks!
  6. M

    Little Headlight Help

    Would any of you guys care to lend me a stock headlight and corner (preferibly from the same side? I'm starting a little project that I need some exact dimensions of the headlights and side markers for. I'd use my own lights, but the stang is my daily driver, so it'd be a huge pain in...
  7. M

    Front Control Arm Bushings

    I am in the process of redoing my suspension. In the future I plan on getting the MM K-member and their tubular control arms to make a little extra room for running the plumbing for turbos. The problem is that I don't have the cash to drop on new control arms and a k-membem. Rather than...
  8. M

    Non-Mustang Car Help

    Hey everyone! I've got a really crappy running 1992 Pontiac Bonneville with the 3.8 V6 in it (I know, I know, its not a mustang, but you guys know your stuff). Just about every time I hop in it to drive, it starts right up without a hitch. If I rev it up a little it falls flat on its face and...
  9. M

    Need Help Quick w/ Quadrant Install

    I'm installing a Fiore quadrant and FWA tonight and ran in to a problem with the quadrant installation. When I put the quadrant on the two rods there is a heck of a lot of side-to-side play when I put the cotter pins back in, even with the little 1/8" thick spacer that came with the quadrant...
  10. M

    Oil in Intake

    I pulled off the cover of my Performer intake today and found about half an ounce or a little more of oil in my upper intake. I installed the intake last summer and didn't find any oil in the stock piece. While I was installing the new intake I replaced the PCV valve and cleaned the screen...
  11. M

    Floating Idle and Dying

    I was driving my 95 GT around yesterday running some errands. Whenever I would go to start my car again the idle would float around from about 500 to 1200 RPM (500 when it was just about to die and then catch itself and shoot up to 1200). If I would rev the engine a little before it died it...
  12. M

    Oil Pan

    I've got a '95 GT that is basically stock, aside for an Eddy Performer and the usual bolt-ons. A couple weeks ago I was at my buddy's house and we threw my car up on his lift. While walking under it, I noticed that my oil pan is looking really rusty... as in metal is flaking off and such...
  13. M

    Electrical Help

    I'm having a bit of an electrical problem with my '95 GT. Two weeks ago I went to start my car after letting it sit for three or so weeks (I know, its a sin, but I'm at college). It barely turned over when I turned the key, so I jumped it and it started fine. This Monday I went to take it for...
  14. M

    Engine Running Differently (bad differently)

    Last weekend I installed an Edelbrock Performer intake on my '95 GT. Everything went well aside from loosing the timing, as I pulled the distributor, but I planned on advancing the timing a little anyway. When I was finished, I had set the timing at 14 degrees with no pinging. The engine...
  15. M

    Stereo Problem

    I have a problem with my stereo that I was hoping you guys could help me with. This past spring I got my 1995 Mustang out of storage and as I was replacing the battery, I blew a fuse (bad battery, long story). The fuse was the one that powers the stereo, speedometer, odometer, etc. I...
  16. M

    CarFax Report Please

    My friend is looking at a car and needs a Carfax report done on it. Could someone please run the VIN 3FAKP1134XR172969. If you could also send the report to: [email protected] I'd really appreciate it. Thanks a lot!
  17. M

    Subframe Connectors

    I bought a 1995 GT Mustang coupe two years ago. It came with Steeda weld-in, tubular subframe connectors. I believe this is the part number: 555-5220. They just don't seem like they'd help that much. Any hoo, would I see an improvement if I cut the standard length Steeda's off and...
Top Bottom
Back
Forums
Menu