Search results

  1. 1995GTStang

    T45 throwout bearing issues

    I have a 97' GT. My throw-out bearing damn near seized up on me. It looks like it scored the bearing shaft from the front of the transmission. How difficult is it to replace these and where do you find them? Thanks
  2. 1995GTStang

    1996 GT Automatic trans issues

    I was just helping a friend of mine who has a stock 96 GT automatic. The car runs good but when he attempts to hard accelerate the car studders and spudders and bangs...but does not take off. The car will drive just fine, but its only impacted at full throttle. Any suggestions??
  3. 1995GTStang

    Having problems finding right speedo gear

    I just swapped to 3.73 from 2.73 gears. The place that did the work put a black 20t speedo gear into the T45 transmission. At 60mph my speedo was saying I was doing 71-73mph. I swapped out the 20t for a red 21t speedo gear and now at 60mph its says I am doing closer to 65mph. Has any one...
  4. 1995GTStang

    2.73 to 3.73 gear swap

    I am having my gears swapped in my 97' GT 5 speed. I recently did a 4.6 PI engine swap and with a 70mm BBK throttlebody and CAI setup. It has a highflow catted x pipe and flowmaster mufflers. What approx should I be running in the 1/4 after gears? and then after a decent tune? Thanks
  5. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    I just put a 2002 PI engine in my 97 GT. Before Idropped it in, put new head and intake gaskets etc......I did not replace 1 intake gasket because Mustangs unlimited forgot to send me two...:( The problems I having is....its fires right up idles just fine but when I tap on the throttle it...
  6. 1995GTStang

    Dropping an 02's PI engine in a 1997 GT...

    I was wondering if anyone here has dropped a PI motor and t45 transmission mounted together? I am dropping in an 02 motor in my 97 GT and I am struggling with getting the t45 to mate with the block. I can get the teeth of the shaft to engage the clutch disk about half way then it acts like...
  7. 1995GTStang

    1995 GT sitting funny

    I went out to move my Stang yesterday before it was submerged in the ever flowing water here. I noticed that car was sitting funny......The passenger side rear is approx 2.5-3" shorter than the driver side. The driver's side rear seems to have about a 2.5" gap to the top of the tire while the...
  8. 1995GTStang

    converting to 24lb injectors

    I know most of you have probably answered this question 100 times. My question is...I am doing a Cobra convert to my 95 GT. I am currently running a 302 .30 over with GT40 intake and GT40P heads. Along with a F303 cam, 1.7 roller rockers, SCT chip, BBK shorties and cold air intake. I...
  9. 1995GTStang

    Spark Plugs- Swapping to GT40P heads

    Swapping from stock E7TE heads to GT40P irons. Can I reuse the NGK V plugs I got? Or should I go with the recommended ones for the Explorers? Thanks
  10. 1995GTStang

    Pulling Cats

    I am looking at pulling the cats and just going with an x-pipe to the mufflers. Is this a difficult procedure? What do you do with the pipe that comes off the heads to the cats? Can you just cap it off? Thanks
  11. 1995GTStang

    what the heck is this??

    I was having some serious issues with my a week ago. Come to find out there is a cable attached to my PCM unit with a dial on the end that goes from 1-6. Only one number works on this that allows my car to run normal. If it is on any other number the car barely idles and the CE light is on...
  12. 1995GTStang

    KAM fuse location code 511

    Where the heck is the Keep Alive Memory fuse in these 95 stangs?? I just got a code 511....says check my KAM fuse. Thanks
  13. 1995GTStang

    19# injectors from a 4.6

    I have a set of F4SE-A1B injectors off what I was told was a 4.6. They are 19# and have the same connector as the mustang. They also appear to fit as well. Will these work or is there a resistance issue?? Thanks
  14. 1995GTStang

    95 GT Wont idle

    I just did a gt40 intake swap. I drove the car for a bit got it to running temperature then parked it for a week. I tried firing it up yesterday and now the car does not idle, except when I hold on the gas. It smells like it is running extremely rich. Also the electric fan is running non...
  15. 1995GTStang

    A good intake gasket

    Needing a good intake gasket for stock heads to gt-40 (explorer intake). Any suggestions
  16. 1995GTStang

    symptoms of a bad TPS sensor

    What are they symptoms of a bad TPS sensor?? My idle is rough.....well rougher than normal. I checked for vacuum leaks and found nothing. I have already replaced the IAC valve. The idle acts like I am running a huge cam. It has crane 1.7 roller rockers and some larger looking than...
  17. 1995GTStang

    Procomp motorsports gaskets.....great, good, or OK

    I ordered a gasket set off ebay from Procomp Motorsports. Has any ever used these gaskets before. They look very similar to felpro gaskets. Just wanted to get some input... Thanks
  18. 1995GTStang

    Having some SERIOUS issues after intake swap...HELP!!

    After installing a GT 40 intake and hooking up all the vacuum lines. I fired up the car and there is a very loud knocking sound coming from the top end. It sounds like lifter or pushrod to lifter sound. What is causing this?? I have played around with the timing a little bit to see if I...
  19. 1995GTStang

    possible Cobra 5.0 engine swap?!?!

    I just tore off the intake manifold and valve covers to do a GT40 intake swap and came across crane 1.7 roller rockers that are factory on 93-95 cobra's. On further inspection of the heads seem to have larger intake runners than I remembered of stock E7 heads. Is there any way to tell if I...
  20. 1995GTStang

    Looking for fuel line disconnect tool

    Does anyone have a part number for the fuel disconnect tool at the fuel rails for these 94-95 GT's? I have went to the local napa and they sold me the wrong one. I did not realize this was going to be that difficult. :/ :mad:
Top Bottom
Back
Forums
Menu