Search results

  1. foghorn67

    silly inner fender question

    I need to replace the inner fender piece behind the shock tower on the drivers side. It's causing my hood hinge to bend in all sorts of directions. I swore it's an involved process to take off the outer fender to get to this. Which means unbolting it from the radiator support, and taking...
  2. foghorn67

    at first you don't succeed, try try again.

    Hi, long time, no see. Not really tech, so it goes in the talk section. Last September I had the drivers side headgasket go south for the winter. I finally got off my lazy butt and fixed it. Here is why I lost motivation. (pic below) I stupidly left a rag where the cylinder head goes...
  3. foghorn67

    aluminum radiators (universal)

    I am looking at getting an aluminum radiator, but the custom fit ones where no fabrication is needed are expensive (Griffen, BeCool). I'm thinking about getting a Howe or Fluidyne with minimal fabrication (less then a one day ordeal), any input for a 67 stang with a SB radiator support? thanks!
  4. foghorn67

    Scorched a head gasket!

    Hey guys, long time no talk. It's been pretty quiet concerning my Stang, I am mostly worried about work. But I had it running hot for a day, and after that I get a lot of white smoke from the driver's side exhaust, and it wreaks of antifreeze. I am loosing the coolant with no leaks. So I...
  5. foghorn67

    Knott's Berry Farm anyone?

    Who is going to the all Ford's show? I am.
  6. foghorn67

    are mechanical fuel pumps supposed to do this?

    rewind to a few weeks ago...A friend of mine and I ordered our fuel pumps at the same time. I noticed that he could not pull the lever arm on the pump down at all. I opened the box up, and tried mine. Tough, it didn't budge at all. today...I change out my fuel pump. My new one is a holley...
  7. foghorn67

    weird front end squeek.

    From the drivers side. If I push the car up and down by the driver's fender it squeeks and creaks. When turning it does this as well. I had a problem similiar to this on the other side, and it was the upper control arm bushing. My grease gun won't fit on the zerk fitting. because it is...
  8. foghorn67

    Help me pick my new carb

    I have decided to give the Road Demon the boot. It runs way too rich when idling. And it is way oversized. Too bad, she looks pretty. I have decided to get a Street Avenger. But which one? the 570cfm, or 670cfm. Holley recommends the 670cfm for over 300hp. But the old calculation...
  9. foghorn67

    do manual choke holleys have fast idle cams

    How does a manual choke work? just a cable pulling a choke plate? is there a fast idle cam? just trying to make a selection. It doesn't seem southern california is cold enough to warrent an electric choke. :shrug:
  10. foghorn67

    Just got a Linclon Mark VIII elec. rad. fan, now what?

    Just picked one up yesterday. I heard they are really powerful and can move more air then the black magic. do any of you guys know any links or write-ups on this. have any of you done this before? thanks
  11. foghorn67

    best placement for o2 sensors?

    I just picked up a couple of oxygen sensors for my stang. one for each cylinder bank. It will be hooked up to an autometer air/fuel ratio gauge, and wired with a switch to select between the two. Where is the best place for the shop to weld in the sockets. immediatly after the primary joins...
  12. foghorn67

    starter heat problems-funny solution

    I was at the tire store the other day and my starter does what it usually does when it's hot. it just barely makes a noise and it cranks slow, and doesn't start until it's cool again. somebody had a sunbeam tiger there, and was more or less familiar with ford's. he said to try running another...
  13. foghorn67

    anybody try Meguiar's nxt Tech Wax?

    Just wondering...thought it might be an answer to Zaino.
  14. foghorn67

    price for used 289 heads?

    I got to get rid of my 289 heads. They are used, in decent condition, and clean. I am not sure if it needs a valve job or any other work, but I need to ebay them fast. They are stock from a 67 C-code. what's a fair price? To make this post not an ad. I will not respond to a PM inquiring...
  15. foghorn67

    who was the member that sold suspension parts?

    There was (is) a member who sold suspension and steering parts from his website. I need new tie rods, and I would like to check it out.
  16. foghorn67

    Legislation to Repeal Old Car Emissions Exemption Reintroduced

    They are at it again... Californians, contact your State Assembly member, and Assemblywomen Lieber and express your oppisition to A.B. 2683 if you are a classic car hobbyists. I just got the letter from SEMA a couple of days ago. I will copy and paste if I hear it's cool with SN.---here is...
  17. foghorn67

    icky

    My header collector collected a plastic grocery bag. it's stuck on there until it melts off. my car has been tear inducing toxic for two days. thought I'd share.
  18. foghorn67

    Best way to remove old window tinting?

    A friend of mine is looking into getting a used truck, and was asking sorts of questions. One of them stumped me. What is the best way to remove the tint? Is there a solution for it? thanks
  19. foghorn67

    okay, did it break or is it really that difficult?

    I was adjusting my headlight, and the bucket bent near the adjuster screw which made the adjuster spring pop out. I tried for an hour and couldn't get the spring hooked back on the back of the headlight door. is it really this maddening? :bang: :fuss: is there a tool for this? or is...
  20. foghorn67

    headlight adjusting screw

    I got to replace my adjusting screw on my headlights, it's the fastener on the top that aims the beam up and down. the screw head is totally stripped. anway, are there two different sizes. I called up a local shop, and they said they have ones that are roughly 2.5-3". Then I looked up one in...
Top Bottom
Back
Forums
Menu