Search results

  1. bullitt 736

    Rearend Rebuild / Gear Install Houston Area

    My rearend has 135k miles and is needing to be gutted and gone through. Who have you used in Houston and would you use them again???
  2. bullitt 736

    Mac O/R H Pipe Install

    I'm thinking about installing the O/R H pipe tomorrow on my '01 Bullitt subject to garage floor temperature. :) I want to make sure I don't run in to any problems so I have a few questions. Mine is the three piece design so that should make it easier to install with no lift (maybe). I know...
  3. bullitt 736

    3650 Tranny Problem

    My car (2008 Bullitt) is making a metallic tapping sound at 1500-2300 rpm after it warms up. Sounds like an old & worn lifter used to sound. It is consistent with rpm whether I'm driving or its in neutral. The motor is 100% ruled out by the dealer tech. Outside tech from Ford confirmed its not...
  4. bullitt 736

    Tire Question

    I'm running 265-35-18 tires on 18x9 wheels up front on my '01 Bullitt. I'm upping it to a least a 275-35-18 soon. Has anyone fit a 275-40-18 up front? I would like a little more sidewall. The 275-40 is 26.6" instead of 25.7 inches.
  5. bullitt 736

    Houston Area Car Lifts

    Anyone know of any places around Houston you can rent a lift by the hour. Too old and tired to keep laying on the concrete. :) Thanks.
  6. bullitt 736

    Houston Area Lift

    Anyone know of any places around Houston you can rent a lift by the hour. Too old and tired to keep laying on the concrete. :) Thanks.
  7. bullitt 736

    Need TSB

    Do we have any Ford techs that can check these TSB's for me? TSB 08-2-4 TSB 08-2-10 A copy of these would be great. Thanks.
  8. bullitt 736

    TOB Problems

    The car is in the shop for TOB replacement again. The clutch is a Centerforce DF that has less than 4000 miles on it. It was installed with new TOB and pilot beaing in April. It was in the shop less than a month ago for TOB and pilot bearing. The input shaft does not appear to be twisted to...
  9. bullitt 736

    COP Resistance

    Can someone tell me the coil ohm resistance ranges for the primary and secondary resistance on a 99-04 COP? My secondary resistance on one coil I checked was 6.0. I know the primary should be a lot less but my digital meter doesn't go low enough. I plan to pick up another one tomorrow...
  10. bullitt 736

    Flywheel Help

    I have a 2001 Mustang GT with the 11" clutch and 3650 tranny. I bought the FRPP nodular flywheel #M-6375-D46. I bought it from 50Resto. It was listed as for use with the 11" clutch. FRPP Ford Dealer confirmed the part number. My Centerforce DF did not fit. My shop told me the bolt pattern was...
  11. bullitt 736

    Post Pics of 1999-04 with H&R Race Springs

    Can anyone post pics of a 1999-2004 Mustang with H&R Race Springs? I've seen plenty with the Sports and Supersports but no luck on the Race springs.
  12. bullitt 736

    Vogtland Springs

    I found a few old posts about these springs but not much info. Is anyone running these on a 1999 to 2004 Mustang? What kind of comments do you have about them? Thanks.
  13. bullitt 736

    Houston Shops

    Can anyone from the Houston area recommend some good shops? I'm near The Woodlands but that will not matter. I want quality work. I'm looking at have some of the following work done: Clutch and flywheel Gears Weld SFC Thanks
  14. bullitt 736

    Engine Miss

    Washed the engine today and now I have an engine miss. SEL cam on. I did not use high pressure and tried to stay away from COP, etc. What do I check first? Will a scan at the autoparts tell me which cylinder is misfiring?
  15. bullitt 736

    StangNet Discounts

    Can someone tell me the major parts suppliers we get a member discount from and how much the discount is? If this is posted somewhere I apologize. Just give me a link.
  16. bullitt 736

    Struts and Shocks

    I have a 2001 Bullitt. I am ordering a set of H&R Sport or Super Sport springs soon. I see on the MM website that they recommend the 87-93 GT struts and shocks for lowered cars. Anyone else use these struts and shocks? Does anyone have any opinions on the KYB struts and shocks? I don't do...
  17. bullitt 736

    A/C Died

    A/C crapped today. I think its the compressor. Oil backside. Anyone recommend a good A/C repair shop in North Houston???? Warranty expired May 28.
  18. bullitt 736

    Clutch quad and firewall adjuster

    Any links or tech articles for quadrant and adjuster installation available. Any help appreciated. 2001 GT 4.6L SOHC.
Top Bottom
Back
Forums
Menu