Search results

I have brand new 95 SVT Cobra R front springs for sale . The specs are below M-5310-R58, Front pair only, Including IRS 700-850 Rate(lb/in) 1.25-1.50" Drop(in.) 351W $125 shipped, Don't forget to add 3% paypal fee

I have brand new 95 SVT Cobra R front springs for sale . The specs are below M-5310-R58, Front pair only, Including IRS 700-850 Rate(lb/in) 1.25-1.50" Drop(in.) 351W $125 shipped, Don't forget to add 3% paypal fee

Hi I have brand new RPM II lower intake manifold for sale, The intake is new and never used or bolted down. This is rare 1st version RPM II lower. I ported the older RPM upper intake to match this lower PRM II intake, This is a spare manifold I kept just in case. It will be a nice add on if you...

I have Earl's performance discontinued version of oil cooler adapter. It's just like the ones that came on 95 Cobra R but better. Comes with -10an fittings and assembled. Fits most Ford engines that use Motorcraft FL-1A oil filter, fits 289 302 351W 390 428 429 460 blocks. This was a spare...

Hi I have set of 03-04 Cobra spindles with almost brand new hubs(couple thousand miles) and brand bew competition engineering bumpsteer kit for sale. These are 5/8" bolt through set up and the spindles are machine reamed($80) to 5/8" bolt through studs. One hell of a set up. I prefer local...

The RPM2 lower manifold is never used and is brand new, I got the manifold to move my rpm range up a little but ended up porting the one i got. you can use this with regular performer or RPM upper manifold, you just have to gasket match the upper intake runner openings that's it. I will throw in...

For sale is edelbrock 70mm throttle body and adapter, RPM2 lower intake manifold. The throttle body and the adapter has about 2000 miles on it, The RPM2 lower manifold is never used and is brand new, I got the manifold to move my rpm range up a little but ended up porting the one i got. you can...

Hello, I am in search of stock uncut 2001 bullitt springs, If you or know someone who has a set(front and rear) Please let me know or PM me. Thank you

Question: are these the correct replacement valve seals for iron gt40 heads? Ford Racing Performance Parts Let me know Thanks:nice:

94-95 Mustang SVT Cobra C&L 76mm MAF Mass Air Intake 76mm - 94-95 GT (19 lb) or Cobra (24 lb) & inlet pipe Part Number: 118 Owners of the '94-'95 V8 Mustang and Cobra vehicles have long needed a complete intake solution to address the key problem areas in the factory plastic air meter and...

94-95 Mustang SVT Cobra C&L 76mm MAF Mass Air Intake 76mm - 94-95 GT (19 lb) or Cobra (24 lb) & inlet pipe Part Number: 118 Owners of the '94-'95 V8 Mustang and Cobra vehicles have long needed a complete intake solution to address the key problem areas in the factory plastic air meter and...

Hey guys. I got another pair of GT40 heads i am working on and wondering if any of you used the crane cams spring kit 44308-1 with your GT40 IRON heads. I have already purchased the kit and I have researched it but the answer was unsure everytime. Some went in without problem and some had...

These heads are OEM GT40 Mustang bare heads, set up for original 1.84/1.54 valves, Refreshed and resurfaced, cleaned/maged/checked and never put back on, The car had very low miles, heads were off the car once. it was a street car, All the water port bolts are helicoiled so you don't ever break...

What's up guys :) I have questions for you guys, When does the shaft mount rockers come into play? like jesel and T&D? is it depending on cam lift size or motor size? When do you actually need them? isn't this overkill on small block ford? I am asking because my engine builder said...

SBF Rocker Arms - 1.7, 7075-T6 aluminum, Pedestal Mount Manufacturer: Erson Cams Part#: E928089 Category: Rocker Arm BILLET-ALUMINUM ROCKER ARMS This high-quality, billet rocker arm is machined from extruded 7075-T6 aluminum; the strongest of aluminum materials. A new pocket design decreases...

SOLD!!! I have set of REAL 3 bar GT40 heads that are 63cc for any takers out there. they are clean heads, Heads have low mileage 70K when i originally got it, I ran it for may be 2 years and put 5000 miles on them. Just got it out of the machine shop, resurfaced and cleaned, They are good...

What are you guys using for aftermarket coolant resovior? I am currently using the canton aluminum resorvior for 94-95 cars but i want to get rid of it and get small 1 quart aluminum one. and mount it some where else. I know that the factory one or canton 94-95 one uses the factory coolant...

I have almost brand new set of 1.6 M-6564-B351 pedestal roller rockers for sale. If you are interested let me know, I will send the picture to your email if you want. Looking to get $200+shipping for it. I paid about $400 new, used for only couple thousand miles. I have 2 sets so...

What's up guys :) I am in the process of getting a window switch but there are so many different kinds... I am mainly looking at the NOS digital version and MSD digital version. One thing i dont get is NOS version is much more smaller then the MSD one.... Are they the same and does the same...

What's up guys I have been trying to correct the bumpsteer on my car for a while now, and i have heard 96-04 spindles sits higher a little then the 94-95 spindles, Is this true?:shrug: Some people have recommended that i use 96-04 spindles for aftermarket K-Member, I have AJE racing K-member...