Search results

Anybody know where to find brake hose for this car, 1980 2,3 auto. My .86 old GT hoses does not fit, and the one i need is approx, or 9/16 at he threads, caliper side. Any other car have the same hose as this, 9" breaks from ford ? Thanks, TA :) this does not fit.. 1979-86 Mustang 5.0L...

Hi. Bought a T&L built engine, .040 bore 302cid last summer. After a while, I discovered a crack in the block near the oilfilter. Rebuildt everything into a 1968 302cid, mustangblock, bored .040 over. Hopefully, little thicker and stronger block? After use my engine as a NA this summer, I...

I have bought an used Stroker engine for my Mustang. The new engine is 28oz.in. balanced. The harmonic dampener installed is Professional Products, 80006 , 9,52lbs , 6.4" ,28,4oz.in. Eagle stroker kit, 347cid. My question is, I have a C.A.T power SFI steel flywheel, 50oz.in from my old...

And so It is, Five mounths to next race : Hmmm , sorry lot of myself, but Its a Fox owners life... :D

Scarry ride, from Dragracing to drifting, in less than 1secound :eek: The Large pin seperating the axle shaft, broke and the broken parts ended up locking the wheels in nearly 80Mph. The damage was most likely done during the launch. 2year old pin. The ring gear and pinion and differential...

Ended this season as a lucky dragracer. Mods for this year are Astro A5 gearbox, heavier steel SFI flywheel, relocated battery to trunk, and Track heat upper instead of the street heat (Trick flow). Ps, used the same car for going 360miles each way, driven to race. 7.451sec :D ( last...

After many years of Pacecarhunting, I bought this car last week. Its a all original Car, C4, 302cid, sunroof, no rust and only 51k miles. My GT runs fine, but a quiet weekend cruiser was on my wish list.. This car was sold as new car in Switserland. Three owner since new. Drove It 572 miles...

Can someone help me with some more info, does it looks like a real Saleen, Anybody know ? Its an -88, supercharged, 320hp engine. Thanks,

:) Feels great, when you beat a Chevy, or :D A nice raceweekend, and my Fox runs fine. After racing sunday, I changed my tires, and drove back home, 366Miles, seven houers. " Driven to race " I think that is why we have cars, or ? :flag: The Nova guy, redlighted, so did I, but he more...

AND, sometimes it just slides sideways... , but its still fun doing a burnout, or ? 7.6 sec eight mile. and and a lot of coffe between the rounds.. FOX life is fun ! :D

Usually Launch at 4500rpm, G60-15 DOT Racemaster tires, 12psi. Strange 10way adj struts/shocks. UPR K-member kit, dobbel airbags,custom springs-rear. :flag: :nice:

Searched around for a Fox, and found this Car : http://www.dealsonwheels.com/search/detail.aspx?id=86474 Is it a rare Car or ?

Dyno numbers after my Procharger, 1P-SC install. 0.73bar (10psi ) boost. Trick flow EFI kit, TFS stage 1 camshaft etc. ( more info at "My Garage" ) Dyno numbers in Flywheel horsepower, (approx 397 RWHP.) (Torque=Vridmoment, Before = Fore, After= Efter, Flywheel hp= Motorhester) Any comments...

Planning to install a compleate K-member kit, including A-arms, coilovers etc. So, I am thinking of this kit from UPR : http://www.uprproducts.com/shopping/shopexd.asp?id=299 What do you think? Any of you installed this, or should I go for another one? QA1, Garantelli?, Maximum motorsport...

Thinking of installing a Gforce T5, Helical cut gear version in my Fox. Anyone have anything to say, good or bad about this gearbox ? http://www.musclemustangfastfords.com/tech/0406mm_gforce/ Thanks :)

My friends nice -91 LX have this strange non glued /fastened area around the rear conv. window. (see pic. ) Should this bee like this, or should it bee fixed against the window ? Thanks for your comments. :)

..Got a charging problem in a Friends -84 GT. We are thinking of installing a One Wire Alt,approx 100+amp instead of OEM setup. Is this as simple as the Powermaster Homepage says http://www.powermastermotorsports.com/faq_s_-_chrome_alternators.html#15 ? Just One wire ? Hoped to get ridd of...

:( well, was worried about this.., and now I got this viberation. Installed my Centerforce Billet steel flyweel and Dual Friction clutch assembly, together with new bolts and bearings and a steel bearing retainer. The new clutch has been carefully breaked in, normal city stop and go driving...

..Would a set of Quality drivshafts, Mooser, STEEDA, etc. 28 splines together with a rebuild Ford limeted slip differensial,with an extra clutch plate work for a street strip setup ? How much stronger is this driveshafts compared to the stock ones..?( Hoped to upgrade to an Eaton unit and 31...

Got partnumbers,Front/Rear Springs, Anyone recognize them ? Removed the Front and Rear springs from a -84GT. Dont know what type of springs thy are, Brand etc.? They are Black, and front Springs have this label on:MOF74.5/6695 , and Rear Springs got the number:E5SC-5560-AA ..? Anyone know ??