Search results

I have to sell this Rack and Pinion setup. I installed the rack under the car but never finished the install. I need the money and will go back to my manual setup. If you buy the rack, you will see that it's never been used, the pump hasn't had a drop of fluid in it and the hoses are unused...

I bought the Unisteer kit and everything went according to plan until I got to the Power Steering Pump. I have a 302 out of a 76 Granada in my Mustang and it's go the stock water pump.... My 302 had a dummy pulley for where the power steering pump should be. The problem is I can't figure...

Ok, Like the name implies, I am new guy to fooling around with mustangs. I look a look at my lower control arm on the passenger's side. It's appears to be bent a little and so do the mounting bracket that it bolts through is definitely bent. I don't think they are suppose to be that way...

Any tips on getting these things out. I crank on them and I get nothing.

I have a 66 with a 302 in it and an autolite 4100. It runs ok but it idles rough as hell. I am not sure why that is.... I am new so as much detail is appreciated. I put it in the garage and it smells of gas so I suspect that part of the problem might be flooding. What's the best way to...

I am using the Roller Bearing Idler that I got from cobra automotive... I haven't noticed a difference (at least not a huge difference) and I am sure it's installed correctly. I was thinking of switching to the Moog idler arm if I can't get this better. Any thoughts ?

I bought a crappy Grant steering wheel. The horn button keeps popping off. On top of that, the horn button seems to stick when it is on. My question is this, if I switch Grant wheels to one that has a horn built into it, do I have to get another adapter or can I used the one on there. I have...

I have a rebuilt Autolite 4 barrel. I look at the choke and it's slightly open. I never adjust the screws at all. I put the carb on but I realize that my heat tube coming off the exhaust manifold is rusted and broke off. I get the car to start but it idles rough, I pull the throttle...

Anybody know of a set of videos I can buy that will help me with my car. Learning the ins-outs. I'd especially like to learn more about "tuning" my car. An instructional vid would be nice to help walk me through changing the intake and carb, setting timing etc.

Did a search and didn't find anything so I will ask. I moved the emergency flasher to get better access under the dash for a few minutes. I noticed something wierd. When I put it back in place it seemed to blow a fuse. I double checked it. I replaced the fuse then when I wiggle the flasher...

Is it possible to have a short in my Grant steering wheel even though both wires are disconnected ? Second question, who makes a steering wheel WITH a horn that doesn't have a pop off cap ?

I want to double check and make sure I got this correct. I was having trouble with it starting. I get the click click click. I jump it and it starts right up. I put the charger on it and it will take a charge but the next day it's back to the click click click again. Following the advice...

Anyone with fog lights, where did you do your splicing ? I got the fog lights with the car but no instructions and I am not sure where to splice

I have an Autolite 4100 and here's the problem. I get into it a bit and have a little fun I stop someplace (gettting gas etc) and put it in park and let it idle. When I get back in it, and put it in drive it, it dies. I let it sit for a bit, and it cranks up and drives fine. Could it...

I replaced my tired looking gas cap with a new one. The old one was very loose and I never really paid it much attention. The new one fits really snug and that's great. The old gas cap was missing the rubber seal. Now the engine seems to be a little sluggish now. My thoughts are to check...

The new chart is done. This is one is to help people with clearance issues from top to bottom, i.e. motor mounts to hood. If I missed any fields let me know. I appreciate everyone's suggestions and comments. By the way comments are limited in the DB to only 120 characters so be brief...

I am having trouble getting this idler arm off. I have tried banging on the center link with a hammer. I am just trying to get it off so I can put a roller bearing kit in. If I could get the bushing out without having to take it off that would work as well so any tip to help get the kit...

I know Summit Racing sells the APC conversion kit but they won't get any in until 11/15. Anybody know of a location where I can buy the conversion kit so I don't have to wait ? I would prefer to not make the relays. Painless makes a relay kit but I don't see any reason to pay twice as much.

Ok I have a 302 that the PO told me came out of a Granada. He showed me the mild mods he made to the car but he never got around to putting new headers on it. Stock manifold on it now. I went online and looked for 302 tri-ys and found quite a few of them but some of them say they will fit...

Could you guys post some before and after pics ? Have a buddy who needs some inspriation on his new project car !!!! LOL