Search results

  1. HoofnIt

    R ARP head bolts reusable?

    I know that the factory bolts can only be used one time but can I reuse the ARP fasteners? THX
  2. HoofnIt

    Long tube header question...

    Those of you who have long tubes, do you have to remove the headers in order to take the tranny out? I have shorties and am contemplating stepping up to long tubes but I'm wondering what kind of headaches go along with them? THX
  3. HoofnIt

    Head gaskets installed backwards???

    What would the symptoms be if the head gasket's water ports did not line up right (the front was towards the back)? I mean I know that this would compromise the flow of the coolant but how hot would it run? Has anyone had this happen to them? I'm not an expert in this area but my car runs too...
  4. HoofnIt

    How to swap tranny drive gear for speedo?

    Does anyone have a link to a how-to for this? I finally picked up the right parts and was wondering if anyone had any tips or instructions. Thanks.
  5. HoofnIt

    Speedo Gear for 4.10s???

    I just swapped out my 3.55s for 4.10s a few days ago and I can't get the smile off my face! Now that the car is no longer my daily driver I don't mind the steep gear. My problem is that even with my 23 tooth (white) speedo gear my speedometer is WAY off! Can someone tell me how I can correct...
  6. HoofnIt

    One wheel peel; rearend question

    After a recent trip to the track I discovered I have the dreaded one wheel peel. I was wondering if I upgraded to 31 spline axles and traction loc would the ring and pinion gears have to come out? If so, then I guess it would be an opportune time to swap in some 4.10's. THX
  7. HoofnIt

    Can anyone here recommend a quality

    set of diamond clear corners? I don't want the APC ones as I have a pair now that the rubber trim is shot. I've been looking at these on ebay, click here . Does anyone have these? THX
  8. HoofnIt

    Car stalls when stopping w/AC on???

    I just did a PIH swap and the car runs great! The ping is finally gone but now I have a new problem. Whenever the AC is on and I am coming to a stop the car will stall. If I turn the AC off and come to a stop then the car will idle fine. Do you think turning up the idle a little bit will...
  9. HoofnIt

    Hi speed fan ?

    I have suspected the fan was my heating issue for quite some time now. I'm running a Fluidyne, new waterpump, 50/50 mix, NO underdrive pullies, 180 stat, and water wetter. The car will run 210 on the interstate but once you get in stop and go traffic it will creep up to 230. I think I have...
  10. HoofnIt

    Fan testing?

    My car is starting to get a little too hot, around 230 F. I have a Fluidyne, 2 bottles of water wetter, 180 stat, NO underdrive pullies, & had the tuner lower the fan temps. I know it's hot in the desert but isn't 230 240 too hot? I'm thinking perhaps my fan isn't pulling the air it should...
  11. HoofnIt

    Fluidyne ?

    Can anyone tell me what pound radiator cap I need for my fluidyne? I've looked on their website and also in the paperwork that came with it but have yet to find it. THX
  12. HoofnIt

    Drag radial ?

    I am wondering which size rim 15, 16 or 17" would be best for a dedicated set of drag wheels. I have 3.55 gears and thought I would go with a shorter tire so would 15" be best? What is the best width to go with, 6,7 or 8 "? Also are the MT ET streets tubeless? I still have my 16" waffles...
  13. HoofnIt

    Need a favor ? about Flows

    Can someone who is using a Flowmaster American Thunder 2.5" catback exhaust measure the dimensions of the muffler and tell me if the front and back inlets are both offset? I am out of town and would like to order some magnaflow replacements. THX
  14. HoofnIt

    Just got back from the Dyno

    I learned alot today and although I didn't quite reach the 300rwhp mark I am still happy with the outcome and my ping is GONE! The car also feels alot smoother and the fan temps were lowered. stock, untuned 278hp 317tq after tuning 283hp 316tq minus Flowmasters 291hp...
  15. HoofnIt

    Dyno tune this Tuesday

    Is there anything I need to do prior to my dyno tune? The dyno will include a custom burned chip. Should I set my timing back to 10 deg? Does it matter where I have my fp set? I have a 255 Walbro pump but haven't installed it yet. Do you think I should before the dyno? This will be my...
  16. HoofnIt

    Steeda wheels

    Anyone know the cheapest place to get some Ultralights? I really want the chrome 17 x 9s but for $349 ea. that's gonna put a dent in the bank account! THX
  17. HoofnIt

    It only took me 3 yrs and 9 mos ...

    ...to get to 1000 posts! Is that like a record or something? Should I feel any different as a Super Stallion?
  18. HoofnIt

    What coil ....

    ... should I run with my new Crane Hi6 Ignition? I currently have a MSD Blaster and when I ordered the new ignition from Summit they recommended the LX-92. Crane's literature states that most OE coils are compatible. Which coil should I run with the new ignition? THX
  19. HoofnIt

    Dyno Tune?

    Can anyone recommend a good tuner in the Phoenix AZ area? After my recent HCI swap I think it is time to get this thing running to the best of its potential. I don't mind spending the money, I just want a quality tune. THX
  20. HoofnIt

    SPEC break-in

    The paperwork that came with the clutch said to put 450 miles on the clutch prior to doing any 'spirited' driving. After doing my HCI I am REALLY wanting to put my foot in it to see how it does. I have about 125 miles on it now. Should I really go that many miles? Also, after the HCI my...
Top Bottom
Back
Forums
Menu