Search results

  1. Back in Black

    Just Did Motor Swap.. Car Falls Flat On Power

    It's been a while since I've been on here. I had a nice engine build (550 lift cams , new pistons the works). And to male a long story short I paid the shop to fly cut my pistons and they didn't do it. Valves hit, pistons broke, cylinder walls were sliced and 7 grand went away like that...
  2. Back in Black

    Wiring Harness Question On 4v Swap

    I just did the 4v swap on my 2000 GT. Then engine is out of a 99 Cobra. I have a few questuions for the harness plugs. The main one is the female plug right new to the main connector that comes out of the passenger side of the car near the firewall. What is this for? The motor came fully...
  3. Back in Black

    Oh Dammit. . .

    Well, I don't know what happened now but I started my car up today, and before I put it in gear the motor started to miss and heard a large tapping sound. My check engine light is on and its got a large miss all the way through and car wont go over 10 mph. .. . any ideas?????
  4. Back in Black

    Roots type for 2V????

    Who makes em for 99'-'04 besides Kenne Bell and where can I find them?
  5. Back in Black

    Now this just sucks

    Ok, so I did a mild engine build on the car. It had some miles on it and it was time. So I had it bored .30 over and threw in some nice kieth Black Pistons. I figured now is the time for cams. To make a long story short I paid a well known speed shop to set the cam degree and set the timing...
  6. Back in Black

    P&P Heads on a 2000

    Anone know anything about what I can do with this? How much is it gonna run me? Anyone reputiable? Where I can get it done around the Pittsburgh Area???? Thanks, Jason
  7. Back in Black

    Aftermarket heads????

    Does anyone know where I can get a good set for my 2000 GT? In the middle of a nice rebuild and the heads are the last key. I know about the Patriot heads but am a bit confused if I have to buy the intake or what not. Does anyone P&P them on here? Thanks a ton. Jason
  8. Back in Black

    Quick and stupid question. . .

    is the block itself on the 2005 and up GT the same block as a 2000? Thanks guys
  9. Back in Black

    Thinking of going with the DOHC Swap. . .

    Hey everyone. Been a while since I have been on here. Hope all is well. I have just got the engine out of my 2000 GT and have a couple of options. . . 1. build my SOHC or 2. Have a chance for a Mach 1 03 Engine with low miles. My question, other than the computer, what else do i have to...
  10. Back in Black

    Just bought a shortblock. . .where to go from here

    I just bought a shortblcok for real cheap that I may have bored out .30 over. What I was wondering was what all else would I have to do to build a 4 valve 03-04 type engine with a Cobra supercharger. Like, What else would I have do to the car, (computer, fuel system, gauges) and all the other...
  11. Back in Black

    Looking for a good motor set up. . .

    I am looking to build up a short block I am buying. I know I am going to bore her out .30 but not sure what brand pistons, cams (duration too), and intake to go with. I dont wanna make the car undrivable for longtrips and stuff. Just a lot better than stock and still able to go anywhere...
  12. Back in Black

    Dumb Question

    Would a Stock Supercharger from a 2003 Cobra work on my 2000 GT? Thanks
  13. Back in Black

    Bad miss

    Well, I finally had my car in decent working order, and now I have a bad miss after it warms up. The miss occurs when the car is in gear starting from a dead stop til about 2500 rpms, stops, and if you give the car much gas it misses there too. I talked to a tech and he said maybe a coil or it...
  14. Back in Black

    Bad misfire

    I have a misfire in cylinder 8. Dumb question but on a 2000 GT, that is the one in the rear on the driver side. (Nearist to the driver) Correct? Thanks.
  15. Back in Black

    More stupid sproblems

    When ever I start the car, it barley runs. Surges,then drops in idle. NOT the IAC motor. Even after it warms, when I let off the gas, very bad backfireing. If I take it to like 6,000 rpms, car is fine. This all happens when the car is cold. Thanks guys. :flag: I'll make this easier to...
  16. Back in Black

    Harmonic Balencer Question?

    I have a stupid question for you guys. I have underdrives and the HB is on the outside of the new crank pulley. Ok, it's been a few years since I put them on and my question is, My HB seems to be a little crooked and maybe loose. Should I completlt remove it and seal it back into place? Or...
  17. Back in Black

    Help!!!

    Help!!! my passenger side window will not go up!!! Neither switch (driver side or pass) will make it go up. Down is not a problem but it will not budge to go up. Any suggestions on what it could be? Window lift motor? G.E.M. Modual? I kinda whant to have a good idea because if I buy...
Top Bottom
Back
Forums
Menu