Search results

  1. Sonicaceman

    Mac Exhaust Shorty Headers For 2011-13 3.7 V6 In Progress

    i'm sure this will interest a few people out there on this forum. i've been searching and looking for new headers coming out for our 3.7 v6 mustang and i discovered Mac is working on a set, their website has a spot that says parts coming soon and shorty headers is one of them, included in this...
  2. Sonicaceman

    1993 Mustang LX 347 Stroker

    93 LX with 347 Stroker, 320rwhp/370ft.lb tq. 101,000 original miles, originally a VA car so the body is in very good shape, needs a little paint, no rust, over $10,000 in parts, I'm asking $6,000 or best offer. Located in Albion, NY 14411, my email is [email protected] or my cell is...
  3. Sonicaceman

    Intermittent idle issue??????

    okay i have this idle issue that i just can't figure out. my car will run perfect at times and you wouldn't know there was anything wrong with it, but other times the idle will keep jumping as high as 1200 all the way down to almost zero and it stalls sometimes. i can play with the gas and...
  4. Sonicaceman

    bad ignition effects hp, but not tq????

    ok,i have a couple threads on here but i was wondering if i could get some opinions or facts if anyone has them. i dynoed my car about 5 years ago and found out recently the msd 6al was bad. i fixed it and the car runs awesome. so does anyone think my hp numbers could have been compromised...
  5. Sonicaceman

    Edelbrock "E" Streets, good for 400hp????

    i know these heads came out not too long ago and i've done a little research on them, but not a ton. Anyone running these heads, anyone have any personal flow data, or hp numbers with these heads? Edelbrocks numbers are decent, and i guess you can't expect much for under a 1G for heads, but...
  6. Sonicaceman

    oil breather... needed???

    i recently put a strut tower brace on my 93 347 stroker motor. as a result i had to take out the oil breather on my valve cover and replace it with a regular cap. i noticed the car makes a gurgling noise after i drive it for a while and shut it off. when i drive it for more than 10 miles and...
  7. Sonicaceman

    75 amp alt. with under drive pulley's

    okay the 1st thing everyone is going to say is upgrade the alternator. i know i plan on it, but the funds don't allow it and another $200 this year after a new rear end install would be pushing it. anyway i have the stock 75 amp alternator with under drive pullies and my voltage at 7-800rpm...
  8. Sonicaceman

    steeda lowering springs/caster camber plates

    my brother just bought me steeda lowering springs and caster camber plates for my 93 mustang lx hatchback. i have taken out the back springs when i did the lower control arms but i haven't done anything with the front ones ever. what kind of special tools am i going to need here, about how...
  9. Sonicaceman

    practically new clutch grabs high?

    i put in a clutch about 500 miles or so ago and i adjusted it several times underneath and at the firewall where i have the firewall adjustment. The clutch grabs good and strong but it grabs high and not in the middle like it should. i'm wondering if i have the cable that attaches to the fork...
  10. Sonicaceman

    trick flow fast as cast 190cc head

    just wondering if anyone is using these new heads. they are 190 cc twisted wedge fast as cast aluminum heads with 2.02 1.60 valves. if anyone is running these or have any numbers with these on i'm interested. i'm planning on doing some work next year to my car and i'm researching heads, these...
  11. Sonicaceman

    porting Roush 200 heads?

    i have a set of roush 200 iron heads from world products. i've been scratching my head for a long time if it's worth it to get these cleaned up and maybe a mild port job on them. the intake side seems fine on these just the exhaust side. anyone have these heads? and does anyone have any flow...
  12. Sonicaceman

    best 347 h/c/i

    what would be a good cost effective 347 h/c/i combo that will get me about 325rwhp on a mustang dyno for about $2000-$2500? i was wondering if the trickflow kit would get me close, i know the heads are a little small but the kit is well thought out and works good from what i hear. i know...
  13. Sonicaceman

    8.8" rebuild cost

    how much does a general rebuild for an 8.8" rear axle cost?? my rearend is leaking out the front of the pumpkin at the pinion bearing, and clunks like crazy even at low speeeds. all i have to do is let off the gas a little bit and it clunks, the tranny is shaking as a result of this too. i've...
  14. Sonicaceman

    porting heads, worth it?

    Okay i've been thinking about porting my roush 200 heads just because they're not that great and my numbers are crap. I don't want to do a full on port job, i just need the exhaust opened up because that is the part lacking on these heads and maybe a clean up of the rest of the heads to get...
  15. Sonicaceman

    cam suggestions for 347

    what would the best cam probably be for a my 347 stroker roush 200 heads 70mm tb, gt-40 intake, fenderwell cai msd 6a, 24lb injectors, 76 mm maf electric fan, 1.6rr, custom sct chip(reburnable) ford performance coil, t-5 superduty tranny 3.73 gears, 5 spd, mac long tube headers full...
  16. Sonicaceman

    347 stroker combo... good or bad???

    ok, i've been scratching my head about this for a while. i've been working on my 93 mustang for about five years now. i've put on all the goodies. heads, cam, intake, cai, throttle body ignition, gears, stroker, coil, intake manifold, headers, full exhaust, custom chip, dyno tune, you name...
Top Bottom
Back
Forums
Menu