Search results

  1. cobra1923

    Is mixing 1.7 and 1.6 RR with an E cam a good idea?

    hear me out... have a set of 1.6 and a set of 1.7 RRs along with an E cam sitting around. With a set of GT40s (not P) and a gasket matched cobra intake.. would there an advantage that outweighs any disadvantage, to running a 1.7 on the exhaust and a 1.6 on the intake. This would take the...
  2. cobra1923

    slight pop when let off accelerator

    Hello all, thought I could fix it on my own.. but need some guidance. I have an 87 speed density 5.0. All stock save a K and N panel filter, PVC tube to replace the stock rubber intake tube, and flows with dumps right at the axles. I have a pop out the exhaust when letting off the accelerator...
  3. cobra1923

    Mixing RR ratios? Worth it?

    Here's another one I have been chewing on. I am running an E cam that I had laying around. I also have an extra set of 1.7 RR along with a set of 1.6 (both the blue FordMotorsports). I've always liked running the 1.6 to keep the geometry the way Ford intended.. but would it hut to run the...
  4. cobra1923

    .060 overbore and head gaskets

    Hello all, I haven't asked a 5.0 question in awhile but I am getting ready to build up a new engine for my '95. My question is this: I have a set of '93 Cobra GT40 heads that have been machined for a Loc Wire Gasket. The block I am using has a .060 overbore. Do I need to get a specific...
  5. cobra1923

    will 1.6 SVO RR fit under 94/95 valve covers

    I picked up a set of GT40 irons and some SVO 1.6 ped mount roller rockers.. before I get in there and realize there is an issue, will these rockers fit under the 94/95 stock valve covers with just a E cam? I am running a fox body intake, so theoretically, I could just throw on some fox valve...
  6. cobra1923

    Anyone have experience w replacng vert top?

    I need to replace the rear curtain (the piece with the back window in it). Anyone have any idea how it's done? 1995 GT glass rear window w/ defrost. Looks like it might be a zipper along the top and the trim piece holding it on the bottom but want to be sure it's not too hard before I start...
  7. cobra1923

    Experience installing vert top on SN95? Anyone?

    I need to replace the rear curtain in the vert top of my '95. It's got the glass window with defrost. I haven't started yanking things out but it looks like it might be a zipper along the top and held in place on the bottom by trim panel.. Anyone have any experience doing this? I can pick up...
  8. cobra1923

    Cobra 70MM MAF on GT, any issues

    Can I run a 24# calibrated '95 Cobra 70MM MAF on my 95 GT (with the corresponding 24# squirters?)? without any issues?
  9. cobra1923

    complete turbo for 5.0 on ebay?

    I am curious what you guys think of this? $1250 turbo setup that bolts to stock headers? I've always been a supercharger believer, any thoughts? Please do not post links to active ebay auctions. For future reference, you may post the pics from the auction, as listed below. Matt Ps...
  10. cobra1923

    Stock 86-93 HO intake to 94/95 issues

    I picked up an extrude honed stock 5.0 fox body intake to put on my "low buck" 95 project. I'm getting an elbow adaptor, will I need to do anthing else with the internal Fox EGR system? The elbow should block off the internal intake portion of the EGR so I'm thinking everything should hook up...
  11. cobra1923

    Where are ABS speed sensors on 94-95?

    I've picked up a down and out '95 from a friend that needed some help. The ABS started acting up when he got the car back from the shop that put his gears in. Do the 94-95 use the speed sensor/ABS rings pressed onto the end of the axles (near the brake) or do they use a "tone ring" inside the...
  12. cobra1923

    BBk TB install w/ idle issue

    I put in a 75MM BBk TB on my '02 GT. I already had a C&L plenum and everything ran great with the stock TB. The install of the BBK went easy and the car definately pulls a little more above 2500RPM but my idle is a little high now. I set the set screw according to the directions and it idled...
  13. cobra1923

    trouble codes for my '02 GT

    I just installed a Catted UPR x pipe (to go along with my 40 series flows) and some of the piggyback March U/D pullies (until I can afford to get the balancer / pulley combo that March offers). When I put on the pullies, I yanked my timing adjuster (I've since purchased a Diablo tuner, so the...
  14. cobra1923

    Help with UPR catted X pipe

    I picked up a slightly used cheap UPR catted X pipe for my '02 GT. When I search the forums, I read that there is a small extension (?) and a metal gasket (for the passenger side exhaust manifold) that is supposed to be used to not have any leaks. When it arrived I got the 2 pieces of the X...
  15. cobra1923

    Looking for a shop in MD to do gears

    I'm relatively new to the Baltimore area and am having a hard time finding a reasonably priced, reputable shop to put in my 4:10's. Anybody have any advice for me? '02 Mineral Grey GT
Top Bottom
Back
Forums
Menu