I had to sell my project car so now I have a bunch of parts around that I can sell (probably to finance my next project that never gets done 
)
All parts are in Grand Junction Colorado.
- T56 out of 04 Cobra 46xxx miles $1200
-Input shaft is lightly twisted, I have a brand new 26 spline shaft to go with
it.
- TB retaining sleeve is marred up so I have a brand new sleeve also
- 351W roller block complete motor EFI(minus ecm) from bronco? Also will throw in 5.0 cam/rockers/retainer $500
I think it was 69xxx miles, never asked since I was planning to tear down and bore .030 over anyway.
- 408 stroker kit, brand new in box, dish pistons, scat crank, forged H-beams. Sale pending$1600
Scat crank pn - 9-351-400-6000-2100W
this is a 9000 series crank
Scat forged H-beam Rods 2-350-6200-2100
Thought they were I-beam.. was wrong, I upgraded them
Probe Forged 24cc Dish Pistons FPS-P4082F+.030 (XS)
http://www.probeindustries.com/v/dow...009catalog.pdf
page 7 at the bottom, lists dish size, compression ratio's with a zero decked block and different combustion chamber sizes and other misc info.
Rings C9090-30(XS)
Main Bearings 7078M
Rod Bearings CR807SI
- Set of Bare Dart Pro1 195cc as cast heads - SOLD
- Trick flow type R 90mm intake w/90mm maf - $550
I also have some Ron Morris mounts for the motor and transmission to put them into a early model mustang without cutting.... or so they say....
(think earlier than 66 or so you might have to cut anyway) if interested let me know and I'll shoot you a price for the set or whichever you need.
and a complete set of floor pans for a 68 stang coupe.
970-210-8878 Leland
[email protected]
)All parts are in Grand Junction Colorado.
- T56 out of 04 Cobra 46xxx miles $1200
-Input shaft is lightly twisted, I have a brand new 26 spline shaft to go with
it.
- TB retaining sleeve is marred up so I have a brand new sleeve also
- 351W roller block complete motor EFI(minus ecm) from bronco? Also will throw in 5.0 cam/rockers/retainer $500
I think it was 69xxx miles, never asked since I was planning to tear down and bore .030 over anyway.
- 408 stroker kit, brand new in box, dish pistons, scat crank, forged H-beams. Sale pending$1600
Scat crank pn - 9-351-400-6000-2100W
this is a 9000 series crank
Scat forged H-beam Rods 2-350-6200-2100
Thought they were I-beam.. was wrong, I upgraded them
Probe Forged 24cc Dish Pistons FPS-P4082F+.030 (XS)
http://www.probeindustries.com/v/dow...009catalog.pdf
page 7 at the bottom, lists dish size, compression ratio's with a zero decked block and different combustion chamber sizes and other misc info.
Rings C9090-30(XS)
Main Bearings 7078M
Rod Bearings CR807SI
- Set of Bare Dart Pro1 195cc as cast heads - SOLD
- Trick flow type R 90mm intake w/90mm maf - $550
I also have some Ron Morris mounts for the motor and transmission to put them into a early model mustang without cutting.... or so they say....
(think earlier than 66 or so you might have to cut anyway) if interested let me know and I'll shoot you a price for the set or whichever you need.and a complete set of floor pans for a 68 stang coupe.
970-210-8878 Leland
[email protected]
