Search results

Is this the main windshield wiper motor wire...putting my bay together and can't locate where it goes....help??:shrug:

How do I chk voltage on the pump to ensure it is good or not. Turning the key on, the fuel pump makes ABSOLUTELY ZERO noise and car will not fire obviously. This was a carb conversion recently.

I'm running an aluminum griffin radiator and a typical waterpump set-up on my 347. I want to run some stainless braided hose for my upper & lower hoses. I have the 20an fittings and the hose for the set-up. My issue is that the thermostat housing (waterneck) is cast iron. Aluminum and...

Anyone have a set of Kirkey seats in thier car. If so what degree of incline...what model, and do you like them. My car is not a daily driver, so it isn't a factor comfort wise. Anyone have pics! :shrug:

I just installed some 3a seats in my mustang, which look pretty good. Anyway...I would like to stabilize the seat a bit in the back. It sits aboiut a good 4-5 inches from the roll cage, and I was going to install a brace that attaches to the back and welds to the cage. The only bracket that I...

Best place to buy a reverse -rotation waterpump for my 1990 lx?

I just dropped my new 347 in that I recently built. I am going to get the timing set this weekend. The car will start now, but if I do not hold the gas in...it will die within 5-10 secs. Also I am running a mini battery which it seems after every initial start up it drains and has a very hard...

Anybody found that thier mini battery is not sufficint to crank thier car, and went back to a normal battery? It seems to not want to crank my 347. :notnice:

Tried to start my 347 this afternoon....it tried to turn over, but nothing at all. The batteries been in a while, I am charging it now. It s one of those mini batteries and has been new( dormant) in the car for several months. Anyone else have any suggestions or ideas. I am sure that I have...

If you have no smog equipment, what do you guys normally use to plug up the holes in the back of the heads? :rolleyes:

Where the hell does he vacuum hose for the nipple on the EGR valve go...Im having a brain dump! :shrug:

Im having a brain dump and feel like a dumb ass for asking. I can't remember where the PCV valve hose goes to...please help! :bs: :shrug: :rlaugh:

What is the difference, if any....and can I get away w/ just a catch can...and not something that recirculates as long as I keep my radiator full...should it be an issue. I saw a thread where someone actually swapped the fittings and made the catch can into a overflow, they just had to fill it...

There is a black pipe like object that connects to the heater core w/ 2 hoses, and to the water pump...my question is, what is the name of the sensor that screws into it. Brian

I am gonna wire up one in my 1990....Did you have to move your fan over a bit to either side to run it.....it seems as if my wp pulley is in the way. If I did have to move it to either side a few inches., will it affect cooling any? Also, could I drop it down a bit towards the air-dam? Also how...

Just ordered the plastic box from summit....after reading several posts here and on the corral, I have decided that it is probably a peice of ****. I am actually looking at making my own. Any suggestions? -B :shrug:

Where did you guys run the hoses for center a/c console 2 5/8 gauges. I pulled the console out and expected to see a straight shot over to the steering column, but not. Can anyone help me out. :shrug:

I was thinking about going w/ 36# injectors for my 347 im working on. My friend says that they are too big. It will be N/A, but will of course have upgraded cam, heads...the good stuff. Plus a fuel pressure regulator. He says the pulse width of the injectors will be too much? Is he correct, will...

Over the winter...I want to do a 306 buildup for a hatch that I just bought, and wanted to know a good combo and a few good suggestions. I want it EFI...streetable. I will add aluminum heads, and 373 gears possibly.