Search results

Wife has an 03 gt auto. Has stage 2 high tech stage 2 cams, and usual engine bolt ons, 4.10's, edge 3000 converter. She wants a supercharger now, but still drives it on the street quite a bit. So far it looks as the best ones to consider would be the v3 si trim intercooled vortech or the...

Wife has a 03gt and I was going to install these el-glo gauge faces. Everything looks pretty straight forward, but it comes with this steel bracket that has the dimmer knob and switch for the colors. Where in the hell can you mount this to actually use it and NOT be in the way of something...

My pro street car has the new upper uca's about 3 years ago. (not many miles). Bushings are junk, The nuts just keep loosening up all the time. So I am sick of the stock cheap china junk you get with ALL of these kits. ( I have tried damn near all of them). I was looking at either global...

I now have an official 10 sec street car. Went back to Cedar falls IA. First pass off the trailer and it went 10.89@122!! Finally! I knew it would do it. Got in an open comp race for $20 and made it to the semis and won $30. Pulls the wheels real hard. Man is that fun! Then later on, after...

Boy, what a difference a converter can make! Got one through coan. Damn expensive but it works great. Was at BIR in july for a muscle car shootout and with the dot's and mufflers, it ran 11.40's@118. Trans brake did nothing for the car. 1.7 60ft's. New converter - Ran 11.13@119 off the trailer...

Anybody running a lokar cable on a 70 mustang?? I put a vic jr on mine now and the stock cable does work, but it right on the limit as far as length goes. I would like to try a carb spacer, but the cable is too short. If so, what part # did you use?? Thanks much!!:nice:

Many new UPDATES to the cars!! Well been a busy winter (again!). Took my 408 and p.a. c-4 out of the orange mach and put it in my pro street fastback. Added a backbrace, new rod ends, 4.56 with spool, 35 spline axles, new coil over shocks. Also took off the choking dual plane intake, small carb...

I have 2 sets of 70 drum brake setups. I am selling one set. Spindles, complete drums, brakes, hoses everything. Hoses are only 1 year old. $50 obo. Don't know about shipping cause this stuff is HEAVY. Would be better top pick up. I am in S.E. MN. Just email me at [email protected]. Thanks.

I am switching to disk brakes from drum. Both 1970 spindles and hardware. Original 70 proportioning valves. The old valve has 2 lines in the top. They are from the master cylinder. These 2 are the same as the disc vavle. Both valves have 2 line coming out the bottom. I am guessing these...

Got a 4 bolt main cleveland. 1972 block, 1971 4 barrel open chamber heads 1970 doa -L intake. Runs great. Never overheated, Very good oil pressure. Complete long block with intake. I put the stud conversion kit in with harland sharp roller rockers. New mild crane cam with new lifters new timing...

Anybody ever port their intake? Looking for any pics of the plenum area of a ported intake. I have ported many heads and matched the intake but I was wondering how to shape the plenum area and weather or not to open up the whole port (cross section). I have an edel perf rpm on the 408 right now...

Going to be coming to California in Aug from like the 14-28th on honeymoon. Take a couple of day to get there. I have been there when I was young, she's never been anywhere. Going to see the main sites like alcatraz, golden gate, maybe china town, Lombard street, 17mi. drive, maybe universal...

I have an old 750 d.p. that I put on a proform main body. But I think that this problem was there before I did the main body change (it was years ago). I had the engine dyno'd so I know wide open throttle the air/fuel is right where it makes the power and is Plenty safe. Problem is cruising...

Project update w/pics Don't know if anybody remember the first post. Back in Oct? http://forums.stangnet.com/showthread.php?t=588782 Couple of updated pics. Took everything down to the frame. Motor, tranny, rear end, suspension out. Welded up and reenforced shock towers. New front...

The "new" 70 that I just bought seems like the brake pedal is way too high. About 2" higher than the mach. WAY too uncomfortable. Car was originally a 302 car with manual drums. Still has the manual drums. Could somone have put the wrong master cylinder in? Is there a difference in master...

:shrug: What is the correct way to install a battery cutoff switch on a stock 70 mustang elec system?? What wires do you have to run? Thanks much!

Could you do it without much modifications? Just wondering how much different the cougar and mustang hoods are. I like the boss scoop but I think its just a touch too tall. 3" I like the cougar scoop a bit better because it is only like 2 or a 2 1/4" high. Think the cougar one would bolt on...

Never really seen one before so I don't know exactly what this diff is. It is definatly not an open or a 2 or 4 pinion posi. No shafts to hold the side gears. Another strange thing is they resplined some stock 31 spline axles to 28 when they narrowed the axles. Also has 4.86 gears which I...

Just wondering? Do you put take apart the fitting and put the braided line in the one half first? Do you leave the fitting together and screw the braided line into it while it is together? Having an H of a time. Never put any together before. Thanks for any help!

Got a 70 fastback. Just wondering where you guys did or would suggest running the fuel lines. I will run an electric pump from the cell in the back to the front with a return regulator. then return line back to the cell. I moved the battery to the trunk along with the regulator and solenoid...